Sewhacnm SI 460A Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 56

background image

- 10 -

SI 460A DIN SIZE WEIGHING INDICATOR

4-3 Load cell Installation

Load Cell Wire Connection (In case of SEWHACNM’s Load cell)
It depends on the manufacturer of load cell, please check the specification.

※ Load cell wire color can be changed without prior notice.

Under Set-up the Load cell, if EXC+ and EXC- have a short circuit,

It may cause damage in the indicator.(specially analogue board)
If you connect other wires to Load cell terminal wrongly, it may cause
damage in the analogue board.
Before connecting the load cell cable you have to power off and be sure to
connect the cable to the terminal correctly.

Do not weld near the load cells , Indicators or other devices.

Load Cell Installation

1.

You can connect Max 8pcs of same capacity Load cells at once. (350 Ω)

2.

You have to make horizontal balance on the ground.

3.

If you install more than 2pcs of load cells, use Summing box and adjust output signal
difference as minimum. It can make wrong weighing process caused by each load cell’s
variation.

4.

If there is some temperature difference around Load cell, it can cause wrong weight
measurement.

5.

Don’t do Welding job or Arc discharge around installation place. But, there is no
choice, please disconnect power cable and Load cell cable.

If you measure static electricity material, please make earth between down part and up
part of Load cell.

-----Sewhacnm Co.,ltd. Load cell & wire color----

-

«
...
8
9
10
11
12
...
»

Содержание SI 460A

























































Отзывы:

Нет отзывов

Похожие инструкции для SI 460A

Бренд: Panasonic Страницы: 2

Бренд: Ecco Страницы: 9

Бренд: Ecco Страницы: 9

Бренд: Wagan Страницы: 12

Бренд: Natibaby Страницы: 24

Бренд: Narvitech Страницы: 12

Бренд: ICON Страницы: 2

Power commander GSXR750

Бренд: Dynojet Страницы: 4

Бренд: NeuLog Страницы: 4

Бренд: Firecom Страницы: 8

Бренд: Horn Tools Страницы: 6

Бренд: PCB Piezotronics Страницы: 9

Бренд: Nauticam Страницы: 33

Бренд: Growatt Страницы: 10

Бренд: ZALMAN Страницы: 10

Бренд: Yeti Cycles Страницы: 17

Бренд: Cannondale Страницы: 21

Бренд: Tommee Tippee Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды