SEW-Eurodrive MOVI-C UHX25A Series Скачать руководство пользователя страница 44

Страница: 44 / 72

Startup with EtherNet/IP™

Configuration of the fieldbus stations

Manual – MOVI‑C

CONTROLLER standard UHX25A

4. Set the correct firmware version of the EtherNet/IP™ scanner.

5. Enter the IP address of the EtherNet/IP™ scanner. You can find the IP address on

the display of the hardware module.

24493782411

In this example, the name of the EtherNet/IP™ scanner is: EtherNetIPScanner.
The IP address of the EtherNet/IP™ scanner is: 192.168.10.39

5.4.4

Integrating and configuring the MOVI‑C

CONTROLLER in the fieldbus network

The MOVI‑C

CONTROLLER must also be added to the Logix Designer project, con-

nected to the PLC, and configured.

During configuration, the MOVI‑C

CONTROLLER is assigned a logical name, an IP

address, and process data with addresses.

Proceed as follows:

You have already downloaded the device description file (EDS file) of the
MOVI‑C

CONTROLLER from the SEW‑EURODRIVE website →

www.sew-

eurodrive.com

and saved it locally to the engineering PC (see the chapter "In-

stalling the device description file of the MOVI‑C

CONTROLLER" (→

40)).

You have configured the EtherNet/IP™ scanner in the Logix Designer.

25800736/EN – 08/2018

Содержание MOVI-C UHX25A Series









































































Результаты поиска

Содержание MOVI-C UHX25A Series

Отзывы:

SEW-Eurodrive MOVI-C UHX25A Series, Руководство пользователя, Страница: 44 / 72

Результаты поиска

Содержание MOVI-C UHX25A Series

Отзывы: