SEW-Eurodrive MOVI-C UHX25A Series Скачать руководство пользователя страница 24

Страница: 24 / 72

Installation notes

Electrical installation

Manual – MOVI‑C

CONTROLLER standard UHX25A

Station address

EtherCAT

/SBus

PLUS

devices from SEW‑EURODRIVE do not have an address that

can be set on the device. The devices are detected by their position in the bus struc-
ture and are assigned an address by the EtherCAT

/SBus

PLUS

master.

4.2.6

CAN system bus connection

In preparation

4.2.7

Connecting the fieldbus slave

The MOVI‑C

CONTROLLER serves as fieldbus slave for the PLC (fieldbus master).

The communication is realized via Ethernet.

The MOVI‑C

CONTROLLER is connected to the Ethernet network via the following

terminals:

•

X40 (RJ45 connector)

•

X41 (RJ45 connector)

The device is connected to the other network stations, using a category 5, class D
twisted-pair cable in accordance with IEC 11801, edition 2.0.

U H X 2 5 A - E

L/A

X41

X40

X80

L/A

X41

X40

24912804363

INFORMATION

According to IEEE 802.3, 200 Edition, the maximum cable length for
10 MBaud/100 MBaud Ethernet (10BaseT/100BaseT) between 2 network nodes is
100 m.

25800736/EN – 08/2018

Содержание MOVI-C UHX25A Series









































































Результаты поиска

Содержание MOVI-C UHX25A Series

Отзывы:

SEW-Eurodrive MOVI-C UHX25A Series, Руководство пользователя, Страница: 24 / 72

Результаты поиска

Содержание MOVI-C UHX25A Series

Отзывы: