Setra Systems SRPM Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

Setra Systems SRPM Скачать руководство пользователя страница 15

15

4.5 SETUP UNIT OPERATION

ENTERING DATA

Press (or tap) button to select an output or

engineering unit. Selected button background will change from clear to
black.

PASSWORD PROTECTION

Lightly pressing (or tapping) the “Yes” button activates Supervisor
password protection. With Supervisor password protection enabled,
operators can not access menu screens to update setup. Pressing “No”
disables password protection. Pressing “Change” will open “Password
Setting Screen”. To change the password, enter the present password
(numeric value), followed by the new password in the “New Password”
and “Conﬁ rm New Password” entry boxes, then press save. Be careful to
store password for future reference.

Analog Output

Select : 4-20, 0-5, or 0-10

Eng. Unit

Select: “WC, Pa, CmWC

DISPLAY AVERAGING

Lightly pressing (or tapping) the “Display Averaging” box activates the
“Data Entry Screen”). Enter from 0 to 60 seconds. Display averaging
affects the analog output. Increase the display averaging time to smooth
out the pressure readings, this will also reduce the display update rate.

«
...
13
14
15
16
17
...
»

Содержание SRPM





























Отзывы:

Нет отзывов