background image

7

© Setra Systems, Inc. All Rights Reserved. The Setra Systems name and logo are registered trademarks of Setra Systems, Inc.

6.0 Electrical connections

see figure Fig. 5 Voltage output and Fig. 6 Current ouput

EMC recommendations for wiring

The requirements of EMC standards as specified in the technical data are only fulfilled with the  probes connected 

either directly or with Setra original extension cables to SRH400.

•  SRH400 with metal enclosure must be grounded either at the designated points on the inside, or outside at the 

mounting plate. The probe must not be grounded; it must be electrically isolated from the GND.

•  Locate the SRH400, the probe cable and the output cables as far as possible from sources of electromagnetic 

disturbances.

•  For the analogue outputs use either shielded or twisted cable pairs. The shield shall be grounded at one end 

only, preferably at the controller side. 

•  Cable loops may impact on the EMC behavior of SRH400. Keep all cables as short as possible. Unused wires 

shall be grounded at both ends. Run all cables as close as possible to the ground potential, for instance close to 

the walls or steel structure elements.

power supply

for 0 - 1 V:  10 - 35 V DC

  

9 - 29 V AC

for 0 - 10 V:   15 - 35 V DC

  

15 - 29 V AC

power supply

20...35 V DC;  R

L

 <500 Ω

11...35 V DC;   R

L

 <  50 Ω

3

4

1

2

5

SRH400 - Analog volts

SRH400 - Analog millamps

6.1 Connection diagram

Figure 5.

Figure 6.

Содержание SRH400

















Отзывы: