11
SESAMO
DUALCORE
WARNING: misalignments between carriages and sliding guide can cause wear,
excessive noise and malfunctions of the automated system.
VERTICAL ADJUSTMENT (Z) FIG.9
To adjust the height of the leaves and ensure they are perfectly perpendicular to the floor,
proceed as follows (ref.fig.9):
-
Loosed screws G slightly.
DANGER: do not undo the screws G fully as the leaf could fall.
-
Use the level screws H to adjust the height of the leaf
-
Tighten the screws G taking care not to alter the alignment.
HORIZONTAL ADJUSTMENT (X) FIG.11
necessary to adjust the meeting point of the two leaves which must be near the center of
the doorway. The components of the automated systems are positioned so as to match with
the doors in a central position. If it is necessary to change the meeting point during
installation, proceed as follows (ref. fig.11):
-
Loosen screws D relating to the clamp A on the passing branch of the belt (i.e. the
one without joint) so that the comb B allows the belt E to be moved.
-
Move the clamp to the desired position
-
Tighten the screws D, ensuring that the teeth of the belt E sit correctly in the slots
in the comb B
BELT ASSEMBLY AND TENSIONING
to adjust the tension of the belt, proceed as follows (ref.fig.12):
-
ensure that the motor group is positioned and fixed according to the default set-up
and is in a position that ensures the belt is centered in the running area.
-
make sure that D nuts are loose so that the whole assembly can move laterally
-
ensure that screw E is loosed and does not compress spring F
-
ensure that the nuts B are loosed so that slider A is free to move
-
place the toothed belt over the motor pulley and the conduct pulley.
-
move the support unit C to the left until the belt is under a first level of tension.
Check that the two belt branches are visibly taut (without sag)
-
tighten the nuts D of the pulley group on the case
-
turn screw E until the spring F is almost completely compressed (the spirals should
almost be touching). The length of the compressed spring should be between 11-
12 mm.
-
Tighten screws B
Содержание DUALCORE LH100
