background image

 

 
 

SEALED ENERGY SYSTEMS

®

 

User Manual  

      

2.3.4  Disposal 

 

 

Regulations vary for different countries. Dispose of in 
accordance with local regulations. 

 

Intact, spent batteries are not considered to be hazardous 
waste.

 

 

Waste Treatment Methods: Waste Li-Ion batteries meet the 
United States federal definition of a solid waste per 40 Code 
of Federal Regulations (CFR) 261.2. It is recommended that 
the batteries be recycled even though they can be disposed 
of in the garbage

.  

 

Recycling: Waste Li-Ion batteries do not fall under any 
specific RCRA, F, K, P or U lists. The status of scrap Li-Ion 
batteries should be confirmed in the nation or US state 
where disposal occurs

.  

 

2.3.5   Comply with Waste Regulations: 

India:

 

Expended  battery  must  be  taken  for  recycling  or 
disposal at an appropriate collection depot by suitably 
licensed contractors in accordance with state and center 
government regulations.  

USA

:  

Expended  batteries  are  not  considered  hazardous 
waste.    Cells  and  batteries  involved  in  a  fire  may  be 
considered  to  be  hazardous  waste.  Dispose  of  in 
accordance  with  local,  state  and  federal  laws  and 
regulations. 

Consult 

universal/hazardous 

waste 

regulations  for  further  information  regarding  disposal 
of  spent  batteries.  If  the  internal  cells  are 
leaking/broken  open,  consult  hazardous  waste 
regulations  under  US  Environmental  Protection 
Agency’s  Resource  Conservation  and  Recovery  Act 
(RCRA), waste code: D003(reactivity). Also, consult state 
and local regulations for further disposal requirements. 

Canada: 

Expended  battery  packs  are  not  considered  hazardous 
waste.  Cells  and  batteries  involved  in  a  fire  may  be 
considered  to  be  hazardous  waste.  Dispose  of  in 
accordance  with  local,  provincial  and  federal  laws  and 
regulations.  Consult  the  Canadian  Environmental 
Protection Act for additional details.  

EU: 

Expended  battery  pack  waste  must  be  disposed  of  in 
accordance  with  relevant  EC  Directives  and  national, 
regional  and  local  environmental  control  regulations. 
For  disposal  within  the  EC,  the  appropriate  code 
according  to  the  European  Waste  Catalogue  (EWC) 
should  be  used.  EU  Waste  Code:  16  06  05  –  other 
batteries and accumulators. 

Australia: 

Expended battery packs must be taken for recycling or 
disposal at an appropriate collection depot by suitably 
licensed  contractors  in  accordance  with  government 
regulations. 

Содержание SE-2020

























Отзывы: