Servomex AquaXact 1688 Скачать руководство пользователя страница 5

AquaXact Issue 1.0 

© Servomex Group Limited 2017 

5

 

Introduction 

 

About this manual 

1.1

1.1.1 

Scope of the manual 

This manual covers the installation, operation and routine maintenance of the AquaXact 

1688 Dew Point Transmitter. It is intended for those already familiar with the installation, 

use and maintenance of analytical or process instrumentation. 

1.1.2 

Safety information 

Read this manual and make sure you fully understand its contents before you attempt to 

install, use or maintain the device. 
The following icons are used throughout this manual to identify any potential hazards that 

could cause serious injury to people. Always follow the safety instructions and be aware of 

the hazard. 

 

This symbol warns of specific hazards which, if not taken into account, 

may result in personal injury or death. 

 

This symbol warns of specific hazards due to high voltages which, if not 

taken into account, may result in personal injury or death. 

 

This symbol warns of specific hazards due to high temperatures which, if 

not taken into account, may result in personal injury or death. 

 

This symbol warns of specific hazards due to hazardous substances 

which, if not taken into account, may result in personal injury or death. 

 

This symbol warns of specific hazards due to caustic or corrosive 

substances which, if not taken into account, may result in personal injury 

or death. 

 

This symbol highlights where you must take special care to ensure the 

equipment or property is not damaged. 

1.1.3 

Other information provided by the manual 

Note:  Notes give extra information about the equipment. 

Hint: 

Hints give helpful tips and highlights information which is useful for you to be 

aware of, for example, specific operating conditions. 

Содержание AquaXact 1688







































Отзывы: