DA
L
19
65
LEARNING THE RADIO CONTROL CODE
The circuit board incorporates a dual-channel radio receiver at 433.92 MHz, which allows to control the gate at a
distance via micro switch remote controls from the OG/02, OG/04 range and self-learning remote controls from the
OG/62, OG/64, OG/28, OG/48, OG/52, OG/54, OG/82/1 and OG/84 range. Both of the channels are used exclusively to
control the gate. In particular channel 1 of the radio receiver acts from start, while channel 2 acts from the pedestrian.
DELETING CODES IN THE MEMORY
The deleting of all radio codes memorised is carried out by pressing and holding the P3 (PROGR.) and P1
(PAUSE) keys at the same time until the DL6 LED switches off (about 10s) without sending any radio code.
!
ATTENTION: - before using a remote control, perform the programming procedure.
- the maximum number of codes that can be memorised is equal to 32 as start
c 32 for pedestrian control (other combinations are not possible e.g. 40
start + 24 pedestrian etc.) . Below two examples of codes that can be memorised:
- example A:
32 self-learning remote controls
OG/62, OG/64, OG/28, OG/48, OG/52,
OG/54, OG/82/1 and OG/84 as
start
control (e.g. left button) +
32 self-
learning remote controls
OG/62, OG/64, OG/28, OG/48, OG/52, OG/54,
OG/82/1 and OG/84 as
pedestrian
control (e.g. right button)
- example B:
31 self-learning remote controls
OG/62, OG/64, OG/28, OG/48, OG/52,
OG/54, OG/82/1 and OG/84 as start control (e.g. the left button) +
1 micro
switches remote control
OG/02, OG/04 as
start
control (the others do
not have to be memorised OG/02 and OG/04 just set the micro switches in
the same sequence as that memorised) +
31 self-learning remote
controls
OG/62, OG/64, OG/28, OG/48, OG/52, OG/54, OG/82/1 and
OG/84 as
pedestrian
control (e.g. the right button) +
1 micro switches
remote control
OG/02, OG/04 as
pedestrian
control (the others do not
have to be memorised OG/02 and OG/04 just set the micro switches in the
same sequence as that memorised)
!
LEARNING START CODE
- With the control unit powered and the gate closes, press key P3 once (PROGR.) to enter programming. The DL6
LED starts to flash to indicate that the control unit is in the programming state.
- Press the remote control button (e.g. on the left), which wants to act as start control and hold it down until the DL6
LED switches off. The control unit has memorised the radio code received and automatically leaves programming,
setting itself for normal functioning.
- Repeat the procedure if several remote controls must be memorised.
LEARNING PEDESTRIAN CODE
- With the control unit powered and the gate closes, press key P3 twice (PROGR.) to enter programming. The DL6
LED starts to flash quickly to indicate that the control unit is in the programming state.
- Press the remote control button (e.g. on the right), which wants to act as pedestrian control and hold it down until
the DL6 LED switches off. The control unit has memorised the radio code received and automatically leaves
programming, setting itself for normal functioning.
- Repeat the procedure if several remote controls must be memorised.
12 3
4 5
6 7
8 9
10
12 3
4 5
6 7
8 9
10
!
MODIFY THE FACTORY
CONFIGURATION TO PREVENT
UNDESIRED CONTROLS
CONFIGURATION OF MICRO SWITCHES ONLY IN THE CASE OF OG/02 AND OG/04 REMOTE CONTROLS
Only if OG/02 and OG/04 remote controls with micro switches are used, before performing learning of the codes on
the receiver, the factory configuration of the micro switches must be modified to prevent undesired controls
ATTENTION: before starting first programming or deleting the remote controls, temporarily
disconnect the antenna to prevent the receiver from acquiring other signals during this phase,
which may cause incorrect functioning of the automation. Re-connect the antenna when the
procedure has ended.
Page 10/12
C
R
/4
1
/2
4
I
E
