background image

E

R

A

I

S

GATE OPENER DIVISION

C

R

/4

1

/2

4

 I

 E

DA

L  

19

65

CR/41/24  

29.41/24

  CONTROL UNIT FOR CONTROL OF 1 OR 2 24 Vdc MOTORS FOR THE 

AUTOMATION FOR WING GATES

Page 1/12

INSTRUCTIONS FOR INSTALLATION

Thank you for having chosen SERAI ELETTRONICA, certain that you will obtain the performance necessary for use 
from this product.

Remember that you are about to install a 

system 

classified as "motorised activation destined to move gates and 

automatic doors in commercial and residential buildings, with access of vehicles and persons", which is considered 
as 

potentially dangerous

. Normally, it is your task and responsibility to make this system "safe" for how mush this is 

reasonably possible.

Installation and maintenance of such a system must therefore by carried out exclusively by 

train, qualified and exert 

staff

, with 

"state-of-the-art" executions

, as prescribed by law 37/08 and successive amendments and integrations.

 

The law prohibits the realisation of these types of plants by unqualified staff

.

On realisation of its own products, SERAI has respected the following:

Reference Directives for CE marking:

machinery:

2006/42/EEC

low voltage:

73/23/EEC + 93/68/EEC

electromagnetic compatibility:

2004/108/EEC

General reference Standards:

electrical safety:

IEC EN60335-1 + IEC EN60335-2-103

electromagnetic compatibility - emissions:

IEC EN61000-6-3

electromagnetic compatibility - immunity:

IEC EN61000-6-1

When installing the system, as well as that mentioned previously, please also respect.

General reference Standards:

safety of electrical plants in general environments:

IEC 64-8 V2

Reference Standards specific of the product:

safety regarding use of motorised doors - requisites:

UNI EN12453

safety regarding use of motorised doors - test methods:

UNI EN12445

The SERAI products allow to realise systems that respond to these Standards. The following is very important 

THE INSTALLER IS RESPONSIBLE FOR THE SYSTEM AND ITS FUNCTIONING IN COMPLIANCE WITH 
STANDARDS

This manual must be read completely before proceeding with installation of the various parts of the plant.

!

Содержание CR/41/24













Отзывы: