Sera PROFIBUS Скачать руководство пользователя страница 29

Страница: 29 / 32

www.sera-web.com

Diagnostics signals

The

sera

INTERFACE MODULE has two diagnostics messages that are output in the network-specific protocol (PROFIBUS / PRO-

FINET). A present message is indicated by flashing once for a short time of the Module Status LED. The messages can be read in

plain text using the diagnostics function of the Engineering tool.

The following messages can be generated:

■

PUMP_WARNING

There is a signal in the pump. The pump is still operational.

■

PUMP_ERROR

There is a fault in the pump. The pump is not operational.

■

ALARME_STATE

The module can be used to evaluate the error.

Error message

Possible cause

Corrective action

Fault bus module

Module has been removed from the pump

during operation.

Disconnect voltage.

Connect module to pump.

Switch on voltage again.

Fault bus module

Internal error of the communication

module.

Please contact the manufacturer.

MESSAGE

Содержание PROFIBUS

































Результаты поиска

Содержание PROFIBUS

Отзывы:

Бренды по названию

Популярные бренды

Sera PROFIBUS, Техническое руководство

Результаты поиска

Содержание PROFIBUS

Отзывы:

Бренды по названию

Популярные бренды