Sera PROFIBUS Скачать руководство пользователя страница 15

Страница: 15 / 32

www.sera-web.com

OPERATION

Modules / Input

PUMP_CONTROL

This module is always necessary for the control of the pump irrespective of operating mode. The External Stop Bit that is valid

in all operating modes can be set with this module.

Other functions are the setting of the operating mode, reset of the totaliser, acknowledgement of alarms, stroke control for motor

pumps. If a valid interface operating mode is selected and the pump is not in interface operation, it automatically switches to

interface operation.

MANUAL_CONTROL

Adjustment of the stroke frequency / litre capacity in manual mode.

The operating mode in PUMP_CONTROL must be set to Manual Interface.

PULSE_CONTROL

A pulse for executing a stroke can be sent to the pump using the pulse bit. The pulse is detected during a flank change from

0 to 1. Furthermore, the functionalities of pulse parameters are shown. The stroke frequency / litre capacity can be set using

other input data.

ANALOG_CONTROL

Used for operation of the pump using analogue signal. The functionality of analogue parameters is shown via the input data.

A module for parametrisation of the analogue input is required for the operation.

BATCH_CONTROL

Start of a batch, reset of the remaining batch and changeover between „normal“ or „analogue“ batch possible.

Otherwise the batch quantity in strokes / litres and the stroke frequency / litre capacity can be set.

INPUT1_CONTROL, INPUT2_CONTROL, INPUT3_CONTROL

Setting of the inputs analogously to the menu.

OUTPUT1_CONTROL, OUTPUT2_CONTROL

Settings of the outputs analogously to the menu.

A_OUTPUT_CONTROL

Settings of the analogue output analogously to the menu.

MBE_CONTROL, SPEEDLIMIT_CONTROL, SLOWMODE_CONTROL, DOSING_CONTROL,

DEARIATION_CONTROL, LEVEL_CONTROL

Settings analogously to the Extras menu.

TIME_CONTROL

Setting of the system time of the pump.

CALIBRATION_CONTROL

The litre capacity of the pump can be calibrated with this module.

FLASH_CONTROL

Settings for the SD card.

DIACHANGE_CONTROL

Module for performing a diaphragm change. Analogous to the DIACHANGE_STATE status request.

Содержание PROFIBUS

































Результаты поиска

Содержание PROFIBUS

Отзывы:

Бренды по названию

Популярные бренды

Sera PROFIBUS, Техническое руководство

Результаты поиска

Содержание PROFIBUS

Отзывы:

Бренды по названию

Популярные бренды