Sentry Xpress 5.0 Скачать руководство пользователя страница 35

Страница: 35 / 36

Keep the kiln lid or door closed when the kiln is not in use.

Sentry Xpress Ramp-Hold Shorthand Programming

After you press the key(s) in the left column, the message in the center will appear.

KEYS TO PRESS

DISPLAY

COMMENTS

Apply power to kiln

IDLE

Press Start/Stop if IDLE doesn’t appear.

Start/Stop, Up Arrow (NOT down)

USER

Select USER.

Start/Stop, Up & Down Arrows

PR01

Select desired program number (1-25).

Start/Stop

UNLO

Program is locked.*

Up & Down Arrows

0000

Enter passcode to unlock.

Start/Stop

RA 1

Ready to enter a firing rate.

Up & Down Arrows

0000

Enter rate.

Start/Stop

°F

Ready to enter a firing temperature.

Up & Down Arrows

0200

Sample firing rate.

Start/Stop

Ready to enter a hold time, if any.

Up & Down Arrows

00.00

Enter hold time. 00.00 = no hold time.

Repeat for other segments. Enter a rate of 0 for 1st segment not needed.

Start/Stop

LOCK

Do you want to lock the program?*

Up & Down Arrows

0000

Enter passcode. 0000 = leave unlocked.

Start/Stop

STRT

The kiln is ready to fire.

Start/Stop

DELA

Do you want to delay the firing?

Up & Down Arrows

00.00

Enter delay time. 00.00 = no delay.

Start/Stop

-ON-

The kiln will begin firing in 30 seconds.

The kiln is now firing.

*The LOCK and DELA prompts appear only after they have been turned on in Options. To turn them on

or off, see Lock, page 21, or DELA, page 17. This takes only seconds.

Содержание Xpress 5.0





































Результаты поиска

Содержание Xpress 5.0

Отзывы:

Похожие инструкции для Xpress 5.0

Бренды по названию

Популярные бренды

Sentry Xpress 5.0, Инструкция по эксплуатации

Результаты поиска

Содержание Xpress 5.0

Отзывы:

Похожие инструкции для Xpress 5.0

Бренды по названию

Популярные бренды