Sentera Controls STVS1 Series, Монтаж и эксплуатация

Страница: 7 / 9

www.sentera.eu
MIW-STVS1-EN-000 - 24 / 03 / 2022 7 - 9
back to the table of contents
STVS1
230 VAC TRANSFORMER CONTROLLER WITH
ANALOGUE INPUT
6.4
If applicable, connect the unregulated output (L1 and N). It can be used to
supply a 230 VAC valve, lamp, etc. when the knob is not at ‘0’ position (see
Table 1
below).
6.5
Connect the TK contacts for monitoring of the thermal motor protection
to the motor TK terminals. As standard, there is a bridge between the TK
terminals.
6.6
If applicable, connect the 12 VDC digital output (+V terminal) for fault
indication (0V = TK fault; 12 V = normal operation)
ATTENTION A safety isolator / disconnect switch should be installed on the mains electricity
side of all motor drives.
Fig. 3 Wiring and connections
STVS1xxxL22
Appplication example 1: STVS1 + potentiometer MTP-X10K-NA
IN
230 VAC
OUT
230 VAC
L N PE PE L1 N1 N1 U TK TK 0V +12V +V V/C
MTP-X10K-NA
Application example 2: STVS1 + sensor (e.g. RCMFF-2R)
MTP-X10K-NA M M M M M M MT M M M MT M M M MT MT MT T MT T MT T T T T T M M M M MT M MT T MT M M M M M MT M T T M M M MT MT M T M M M M M M M M M M M M M M M M M MT M MT M M M M MT M M M M M T M M M M M M T T T M M M M M M T MT M M M MT MT T M M M MT T MT M M T P P P- P- P- P P P P P P- P- P- P- P P P P P P P P P P P P P P P P P P P P P P P P- P- - P- P X1 X1 X1 X1 X1 X1 X1 X1 X1 1 1 1 1 X1 X1 1 X1 1 1 1 X 1 1 1 1 1 1 1 X X X X X X X 1 1 X1 X X X X1 X1 1 X1 X1 X1 X1 X1 1 1 X1 0 0K 0 0 0K 0K 0 0K 0K 0 0 0 K K K K K K K K K K K K K 0K K 0K 0K 0 0 0 0K K K K K K K K K K 0K K K 0K 0K 0 0 0 0 0K K K K K K K K K 0K 0 0 0 0 0 0 0K K K K K K K K K 0 0 0 0 0 0 0 K K K K K K 0K K K K 0K 0 0 0 0 0 0 0 0 0 K K K K 0K 0K 0 0 0 0 0 0 0 0 0 0 0 0 0 K K K K K 0K 0K 0K 0 0 0 0 0 K K K K K 0 0 0 K K K K 0K 0 0 K K 0 0 0 0K K 0 0K 0K 0K 0 K 0K 0K 0K 0K 0K 0K 0K K N N -N N N N N N N -N N N N -N N -N - N N N N N N N N N N N N N N N N -N N N N N N N N N N N -N N -N - - N N N N N N N N N N N N - - - - - - N N N N N N N N N N N N N - -N N N N N N N N N A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
IN
230 VAC
OUT
230 VAC
L N PE PE L1 N1 N1 U TK TK 0V +12V +V V/C
Make sure the connections are correct before you power the unit.
ATTENTION
7.
Close the cover and secure it with the screws.
8.
Turn the knob at ‘0’.
9.
Tighten the cable glands.
10.
Switch on the mains supply.
11.
The controller needs to be switched via the external device providing analogue
input signal
12.
Make sure the transformer controller can operate normally (consider an isolating