SenTech STC-MBS322U3V Скачать руководство пользователя страница 56

Страница: 56 / 65

No.15S103-01

56/65

STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V

Specifications and Use

’s guide

7.14 Device User ID

Device User ID provides the user access to the writable memory area.
Up to 64bytes data can be stored (The data still remains, even turned off the camera)
When the data is less than 64bytes, please add 0x00 at the end of character.

7.15 Event Control (Only USB3 Vision protocol)

The camera can inform the event inside of the camera to host.

GenICamParameters

EventSelector

IEnumeration
Type

Select EventFunction

EventNotification

IEnumeration
Type

Switch ON/OFF on Event function that was selected EventSelector.
On: Event function ON, Off: Event function OFF

To be enable the Event Selector, please select to be available Event on Event Selector.

The camera event functions are as follows.

Event Exposure Start
Inform exposure start timing inside of camera as Event.
Event ID is 0x9002.

Event Exposure End
Inform exposure end timing inside of camera as Event.
Event ID is 0x9001.

(*) Since Event and Stream (image data) share USB bus, when the Event came up frequently, Stream’s data
transfer rate would be decreased.

Содержание STC-MBS322U3V


































































Результаты поиска

Содержание STC-MBS322U3V

Отзывы:

Похожие инструкции для STC-MBS322U3V

Бренды по названию

Популярные бренды

SenTech STC-MBS322U3V, Технические характеристики

Результаты поиска

Содержание STC-MBS322U3V

Отзывы:

Похожие инструкции для STC-MBS322U3V

Бренды по названию

Популярные бренды