background image

9

Housing Features

Battery Pack

The battery pack is located on the back side of the 

instrument housing.  The batteries are Lithium Ion 

rechargeable.  The batteries are only available from 

Sensit Technologies. 

To remove the battery pack turn the retaining screws 

¼ turn.  Pull the bottom of the pack away from the 

main housing.  Recharging of the battery pack requires 

removal from the main housing.

To replace slide the top tabs of the battery pack into 

the retainers at the top of the main housing.  Push the 

bottom into place and turn and lock the retaining screws.

Charge

Complete

(Green)

Charging

(Red)

Status

(Yellow)

Charger

Connection

The battery pack has LED’s to indicate charge status.  Charging should only be performed in an area 

know to be free of combustible gases.

The battery pack may also be charged while operating in a vehicle. Connect the 12vdc adapter into 

the vehicle power outlet and the external port on the battery housing. This can be connected and 

disconnected while the IRED is operating.

When the charger is disconnected, the words “WARM UP”, “PLEASE WAIT” (flashing) are displayed 

and a 180 second countdown is started/displayed. During the 180 second countdown, the user can 

not perform a measurment until the countdown expires. The instrument will only operate when on 

battery power.

Содержание IRED

















Отзывы: