background image

TDS – Timed Dosing System

Instruciton manual TDS series

Code 0000136687

        rev. 1.1

11

5

MAINTENANCE AND ACCESSORIES

5.1 

For TDS-DD Battery (Digital clock with batteries)

When the led in front of unit lights up the battery remaining life is about 50 hours. Replace the batteries to
avoid missed dosings.

5.2

For TDS DA (Analog clock)

  If the pump has to dose more then 15 minutes it will be necessary to set daily clock at 30 minutes and

adjust trimmer.

  Check Daily clock every week.

5.3

Replacing the squeeze tube

Make  sure  that  on  the  clock  the  left-hand  switch  is  on  the 

“  O  ”

  position  (for  the  TDS  DD)  and  proceed  as

follows:

  Remove the snap-on cover protecting the peristaltic pump.

  Place the thumbscrew holder with the two thumbscrews in a vertical position.

  Remove  the  connector  situated  to  the  left  of  the  pump  from  its  seat  and  pull  the  pipe  towards  the  front

panel. While the pipe  is  being  withdrawn,  follow  its  path  by  turning  the  thumbscrew  holder  in  a  clockwise
direction by hand until the connector to the right of the pump can also be removed.

  To re-assemble, move the thumbscrew holder with the two thumbscrews to a horizontal position.

  Push the connector to the left of the pump in as far as it will go, with the curved part towards  the bottom;

  Press the pipe

 

into its seat, following its path progressively by turning the thumbscrew holder in a clockwise

direction by hand, until the connector situated to the right of the pump has also been seated as far as it will
go.

  Put  the  protecting

 

cover  back  into  place  starting  with  the  upper  edge,  positioning  it  with  the  fitted  edge

towards the pump and pressing it slightly on the sides until it clicks audibly shut

It will now be possible to position the left-hand switch on “ I ” or “ AUTO ” (for the TDS DD), depending on
requirements

Содержание TDS DA-115













Отзывы: