background image

 

 

 
 
 
 
 
 
 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTRUCTION MANUAL

 

 

 

EXPLOSION PROOF/ DUST IGNITION PROOF TYPE LED LIGHTING 

 

Thank you very much for purchasing our EXPLOSION PROOF / DUST IGNITION PROOF TYPE LED 

 

 

 

 

The product should be mounted properly according to the instruction manual, on a surface robust enough to
support its weight.
Improper installation might cause fall of the product, an electric shock or injury.

WARNING

The type of protection of this product is as follows:

The product of 14W*2 should be used within an ambient temperature range of -20

º

C to +55ºC.

The product of 15.5W*2should be used within an ambient temperature range of -20ºC to +40ºC.
If the ambient temperature is out of the range, an explosion or fire might result.

Usable in hazardous areas of zone 1 , zone 2 , zone 21 and zone 22 where there is explosive atmospheres.
The product should be of the flameproof type suitable for each hazardous area.
Use of an unsuitable product might cause an explosion or fire.

For electrical connection, be sure to connect the wires in the terminal box securely using crimp-type
terminals, etc. and conduct insulation treatment. An inadequate connection or inadequate insulation might
cause a contact failure, leading to an explosion, fire or electric shock.

GB 3836.1-2010
GB 3836.2-2010

GB 12476.1-2013
GB 12476.5-2013

Ex d 

C

T6 Gb

Ex 

tD A21 IP66

T85℃ 

 

 

Содержание WLZAA14021








Отзывы: