manualshive.com logo in svg

Seiko SII RP-D10 Series, Руководство пользователя, Страница: 30 / 46

Поделиться
Скачать
Seiko SII RP-D10 Series Скачать руководство пользователя страница 30

26 

 

 Bluetooth Communication 

 

(1)  Turn on the printer and pair with the host device. 

In the factory shipment state, the printer enters pairing mode for about 60 seconds with Bluetooth 

LED blinking, by pushing the pairing switch on the back side of the printer for 7 seconds or more.   

During this period, pair with the host device. 

The pairing is conducted by SSP (Simple Secure Pairing), however, PIN code is used when the host 

device does not support SSP. The PIN code is "0000" at the shipping. 

(2)  Conduct Bluetooth connection with the host device. 

After the connection is established, the Bluetooth LED lights up. 

(3)  Check the communication status on the host device. 

(4)  Transmit data from the host device, and verify that the data is printed correctly. 

WARNING

 

◆

 

The printer may affect medical or other electronic devices. Obtain information and 
data concerning influence due to radio interference from the respective manufacturers 
or dealers. 

◆

 

When using the printer in medical institutions, follow their guidelines. 

◆

 

DO NOT use the printer in any area or district where its use is prohibited. 

 

HINT 

•

  The distance of communication is approx. 10 m. However, the distance may differ 

depending on the radio interference and environment. 

 

 

 

 

Содержание SII RP-D10 Series















































Отзывы:

Нет отзывов