manualshive.com logo in svg

Seiko SII RP-D10 Series, Руководство пользователя, Страница: 10 / 46

Поделиться
Скачать
Seiko SII RP-D10 Series Скачать руководство пользователя страница 10

6 

◆

 

DO NOT drop or insert any foreign objects such as clips, pins, and screws into the internal parts or 

slot of the products. 

◆

 

DO NOT drop any liquid or spray a solvent to the products. 

◆

 

NEVER use sharp object such as pen tip to push the switch on the operation panel. 

◆

 

DO NOT use thermal papers taped together. 

◆

 

NEVER pull out the thermal paper when the thermal paper is set. 

◆

 

Make sure not to injure your body or other objects by the plate edge. 

◆

 

Unplug the AC plug from an outlet when something goes wrong with the printer. 

◆

 

NEVER disassemble the printer without a serviceman. 

◆

 

Be careful not to get your fingers or hands caught in the printer when opening or closing the paper 

cover. 

◆

 

In order to ensure the function and the safety of the product, be sure to observe the installation 

direction. 

◆

 

DO NOT connect the RJ connector to a phone line. It should be used as the drawer kick connector. 

◆

 

NEVER connect a USB cable to the RJ connector. 

◆

 

The Bluetooth model uses 2.4GHz frequency range, so if Bluetooth is used around any equipment 

with the same frequency range such as wireless LAN (IEEE802.11b/g/n) and microwave oven, radio 

frequency interference may occur and the communication may become unstable. When it happens, 

turn off the interfering equipment or increase the distance. In addition, shorten the distance between 

the host device and the printer as much as possible. 

◆

 

As the plated sheet steel is used in the printer, the edge face might rust. 

◆

 

When moving the printer from the installation site, hold the printer tightly with both hands, then lift it 

upward slowly to leave the rubber feet from the installation surface. Lifting it rapidly or moving it 

horizontally may peel the entire rubber feet, peel their surfaces, or damage the outer case. 

 

 Thermal Paper Handling 

◆

 

Store the thermal paper in a cool, dry, and dark place. 

◆

 

DO NOT rub the thermal paper with hard objects. 

◆

 

DO NOT leave the thermal paper near organic solvents. 

◆

 

DO NOT allow plastic film, erasers, or adhesive tape to touch the thermal paper for long periods. 

◆

 

DO NOT stack the thermal paper with diazo copies immediately after copying. 

◆

 

DO NOT use chemical glue. 

◆

 

Always use the specified thermal paper. See "18. ACCESSORIES AND CONSUMABLE PARTS" for 

details. 

 

 Precautions on Discarding 

When discarding used products, discard them according to the disposal regulations and rules of each 

respective district. 

 

 

Содержание SII RP-D10 Series















































Отзывы:

Нет отзывов