Seiko LTP F Series Скачать руководство пользователя страница 8

Страница: 8 / 86

viii

FIGURES

Figure

Page

3-1

Heat Element Dimensions (LTPF247) .................................................................................. 3-3

3-2

Print Area (LTPF247) ............................................................................................................ 3-3

3-3

Heat Element Dimensions (LTPF347) .................................................................................. 3-4

3-4

Print Area (LTPF347) ............................................................................................................ 3-4

3-5

Sample Drive Circuit.............................................................................................................. 3-7

3-6

Input Voltage Signals for the Sample Drive Circuit .............................................................. 3-8

3-7

Motor Start/Stop Timing ........................................................................................................ 3-9

3-8

Sample of Motor Current Control ........................................................................................ 3-13

3-9

Thermal Head Block Diagram (LTPF247)........................................................................... 3-15

3-10

Printed Position of the Data (LTPF247) .............................................................................. 3-16

3-11

Thermal Head Block Diagram (LTPF347)........................................................................... 3-18

3-12

Printed Position of the Data (LTPF347) .............................................................................. 3-19

3-13

Timing Chart........................................................................................................................ 3-21

3-14

Thermistor Resistance vs. Temperature............................................................................. 3-26

3-15

Sample External Circuit of the Paper Detector.................................................................... 3-30

3-16

Sample External Circuit of the Platen Position Detector ..................................................... 3-31

4-1

Thermal Head Control Terminals .......................................................................................... 4-2

4-2

Terminals on the Motor Connector........................................................................................ 4-5

5-1

Timing Chart for Driving Using Two Divisions ....................................................................... 5-2

6-1

Printer Mounting Dimensions ................................................................................................ 6-2

6-2

Layout of Printer and Paper................................................................................................... 6-4

6-3

The Platen Unit Mounting Position ........................................................................................ 6-5

7-1

Appearance and Dimensions (LTPF247) .............................................................................. 7-2

7-2

Appearance and Dimensions of the Platen Unit(LTPF247) .................................................. 7-3

7-3

Appearance and Dimensions (LTPF347) .............................................................................. 7-4

7-4

Appearance and Dimensions of the Platen Unit (LTPF347) ................................................. 7-5

8-1

Loading Paper (1).................................................................................................................. 8-1

8-2

Loading Paper (2).................................................................................................................. 8-2

8-3

Loading Paper (3).................................................................................................................. 8-2

8-4

Head Cleaning Procedure ..................................................................................................... 8-4

9-1

Installing the Autocutter Unit (Movable blade unit) ................................................................ 9-2

9-2

Fixing Blade Unit ................................................................................................................... 9-3

9-3

Installing Autocutter Unit (Fixing blade unit) .......................................................................... 9-3

9-4

Clearing a Paper Jam in the Autocutter ................................................................................ 9-4

9-5

Outer Case Design................................................................................................................ 9-5

9-6

Outer Case Design sample (Mechanism Side) ..................................................................... 9-6

9-7

Using the Paper Effectively When Cutting ............................................................................ 9-7

9-8

Appearance of the Printer with the Autocutter Installed (LTPF247 with ACUF224A) ........... 9-8

9-9

Appearance of the Printer with the Autocutter Installed (LTPF247 with ACUF224B) ........... 9-9

9-10

Appearance of the Printer with the Autocutter Installed (LTPF347 with ACUF324A) ......... 9-10

9-11

Appearance of the Printer with the Autocutter Installed (LTPF347 with ACUF324B) ......... 9-11

Содержание LTP F Series























































































Результаты поиска

Содержание LTP F Series

Отзывы:

Похожие инструкции для LTP F Series

Бренды по названию

Популярные бренды

Seiko LTP F Series, Справочное руководство

Результаты поиска

Содержание LTP F Series

Отзывы:

Похожие инструкции для LTP F Series

Бренды по названию

Популярные бренды