Seiko LTP F Series Скачать руководство пользователя страница 79

Страница: 79 / 86

9-5

9.1.3 Consideration for Outer Case Design

(1) Design the outer case of the paper outlet side of the autocutter unit so that the paper does

not go between the outer case and the autocutter unit.

(2) The outer case should not change the paper loading direction sharply in the area around the

paper outlet.

(3) The outer case should be designed so that the user’s fingers or other objects will not be

inserted into the paper outlet.

(4) Inappropriate positioning of the platen and the printer mechanisum may cause cutting failure

and/or paper jam. Pay special attention when designing the outer case. Refer to “

6.4

WHERE TO MOUNT THE PLATEN UNIT

” for positioning the platen and the mechanical

unit.

Figure 9-5

shows a sample outer case design in the platen unit side and

Figure 9-6

shows that

in the mechanism side.

Unit: mm

Figure 9-5 Outer Case Design

Center of reference hole for mounting
the platen unit

Содержание LTP F Series























































































Результаты поиска

Содержание LTP F Series

Отзывы:

Похожие инструкции для LTP F Series

Бренды по названию

Популярные бренды

Seiko LTP F Series, Справочное руководство

Результаты поиска

Содержание LTP F Series

Отзывы:

Похожие инструкции для LTP F Series

Бренды по названию

Популярные бренды