Seg CA01H Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Seg CA01H Скачать руководство пользователя страница 5

5

Ver. 1.0

SHIN HWA Eng.Co.,Ltd.

CONTROL ACTUATOR

CA01H~CA120H

2 Installation

2-1 Structure

When you maintain and check the Control Actuator, please refer to the below diagram.

Fig.-1. Control Actuator structure

2-2 Transport and Installation

Transport

When you transport this product, please avoid an accident such as fall and impact.

Place for Installation

- There is no special limit in the place for installation of the Control Actuator, but if it is exposed

to an environment with bad conditions for a long time, you had better use a proper protection
device.

- As well, you had better secure proper space around the Actuator for maintenance and repair.

Installation

- When you install the Control Actuator in a mounting place selected in advance for installation,

firmly fixate the Actuator with four bolts.

- Connect the lever arm and the corresponding lever.

- The operation angle is correctly adjusted before delivery, and you do not need to adjust it.

If you need to adjust it:

①

Give a current signal (a contact point signal in case of opening/closing control and angle

control) to put the Actuator in a complete opening (or closing) position.

②

Turn off the power supply, and separate the cover on the rear surface of the Actuator from

the main frame. Here, avoid giving a damage to the gasket.

③

Readjust the Position Limit Switch to fit the contact point.

(Refer to Clause 7 later for how to adjust the Limit Switch.)

④

Here, check if the needle of the indicator is in the complete opening (or closing) position

before adjusting.

⑤

Fit the gasket and the cover, close them, and tighten with a bolt.

- Please consult the manufacturer when changing the direction of rotation of the output shaft

«
...
3
4
5
6
7
...
»

Содержание CA01H





















Отзывы:

Нет отзывов