manualshive.com logo in svg

Seg CA01H, Инструкция по эксплуатации, Страница: 15 / 20

Поделиться
Скачать
Seg CA01H Скачать руководство пользователя страница 15

 

15 

 

Ver. 1.0 

SHIN HWA Eng.Co.,Ltd. 

CONTROL ACTUATOR 
 

CA01H~CA120H 

 

3  Maintenance 

3-1 Troubleshooting 

 

Symptom 

Expected Cause 

How To Repair 

Note 

The motor 

does not 

work. 

Power is not supplied. 

Supply power. 

In case of three phase, 
check R, S, and T. 

The position control 
switch operates. 

Reset to fit the scale 
plate. 

 

The torque switch 
operates. 

Remove the cause for 
overload. 

Reset the switch. 

(Never randomly set.) 

The overload relay 
operates. 

Remove the cause for 
overload. 

Reset the set value. 
(Never randomly set.) 

The fuse is broken. 

Replace the fuse. 

In case of three phase 

The condenser is 
damaged. 

Replace the 
condenser. 

In case of single phase 

The brake does not 
work. 

Replace the brake. 

 

The motor 

does not stop 

with the 

position 

control 
switch. 

The motor makes a 
reverse rotation. 

Connection is made 
with two lines among 
three lines changed. 

It is in case of three 
phase, and it does not 
apply to the standard. 

The position control 
switch is changed. 

The position control 
switches (LS1, LS2) 
are used by being 
changed. 

It does not apply to the 
standard. 

The switch setting is 
defective. 

Reset. 

 

The switch is defective.  Replace the switch. 

 

When the 

torque switch 

operates, the 

motor does 

not stop. 

The motor makes a 
reverse rotation. 

Connection is made 
with two lines among 
three lines changed. 

It is in case of three 
phase, and it does not 
apply to the standard. 

The torque switch is 
changed. 

The position control 
switches (LSR, LSF) 
are used by being 
changed. 

 

The switch is defective.  Replace the switch. 

 

Содержание CA01H





















Отзывы:

Нет отзывов