background image

 

Release Version 1.0

 

 

Precautionary and Safety Guidelines

 

The content of this guideline is intended to protect the safety of the user and prevent damage to property. 
Please read these operating instructions carefully and use the device as intended. 

Warning 

(Failure to adhere to any of the following guidelines could result in 

serious injury or death for someone.)

 

■  Make sure to install the product after unplugging the power cord. Also, do not use many 
power plugs at the same time. 

- Doing so could result in abnormal heat, fire, and electric shock. 

■  Do not leave the device in a place where water will fall or splash. Also, don't put anything 
with water on it, such as a flower vase. 

- If liquid gets inside the device, it may cause malfunction or fire 

■  Do not bend the power cord with excessive force. Make sure that the power cord is not 
crushed by heavy objects. 

- It can cause fire. 

■  Do not open the cover arbitrarily as there is a high voltage part in this device. Never 
disassemble, repair, or modify it. 

- Improper work can lead to fire, electric shock and injuries. 

■  Do not install this product in a location with high humidity, dust, or soot. 

- Electric shock and fire may result. 

■  Do not pull on the section of the power cord and do not pull out the power plug with wet 
hands. If the power cord is loose, do not plug it in. 

- There is a risk of fire and electric shock. 

■  Always keep the location clean and dust-free during or after the installation of the device. 
When cleaning the device, wipe it with a dry cloth and do not use water, thinner, or organic 
solvents. 

- Doing so could result in malfunction or fire 

■  Store the device in a cool place out of direct sunlight. Keep it at a reasonable temperature 
and avoid heating devices such as candles or heaters. Also, keep the equipment or tools away 
from places where people go in and out. 

- There is a risk of damage to the surface of the device and the risk of failure, electric shock or fire. 

■  Be aware of potential hazards in the workplace, such as wet floor, ungrounded power 
extension cords, old power cords and lack of protective earth. If you have any problems, contact 
your seller or specialist. 

- Doing so could result in fire or electric shock. 

■  The input voltage required to operate this equipment must have a voltage fluctuation range 
within 10% of the specified voltage, and the outlet must be grounded. Also, do not use 
electrical appliances such as hair dryers, irons, and refrigerators with the outlet to which the 
power plug is connected. 

- Doing so could result in abnormal heat, fire, or electric shock. 

■  During thunderstorms or lightning strikes, pay attention to safety and pull out the power 
plug. 

Содержание SC-IPC3001G















Отзывы: