SECO-LARM SLI Enforcer E-960-D190Q Скачать руководство пользователя страница 10

Страница: 10 / 12

ENFORCER Twin Photobeam Detectors

SECO-LARM U.S.A., Inc.

The response time adjustment knob sets how long the beam can be

interrupted before triggering the alarm (see fig. 11):
a.

A short response time (high sensitivity) is suitable for catching fast
moving intruders, but more susceptible to false alarms.

A long response time (low sensitivity) reduces false alarms, but fast

moving intruders may not trigger the sensor.

Adjust the knob to the site’s situation. You may need to make adjustments
later after the walk-through test.

Adjusting the Response Time: (IMPORTANT)

Testing the Unit:

Power up the transmitter and receiver.

If the yellow or red LED remains steady ON even

when the beam is not interrupted, re-adjust the

alignment.

Walk between the transmitter and receiver to
interrupt the beams. Walk at various speeds, and

adjust the response time as needed.

NOTE

– The alarm will be triggered

only if both the upper and lower

beams are simultaneously interrupted.

IMPORTANT

–Test the detector

periodically to ensure the alignment
and delay time settings are suitable

for the site.

Table 5: Specifications

Model E-960-D90Q

E-960-D190Q

E-960-D290Q

E-964-D390Q

Max. range (outdoor)

90' (30m)

190' (60m)

290' (90m)

390' (120m)

Max. range (indoor)

190' (60m)

390' (120m)

590' (180m)

790' (240m)

Max. current (Tx & Rx)

64mA

70mA

74mA

88mA

No. of beam channel

N/A N/A N/A 4

Voltage output (+/-10%)

1~4 V

Power

10~30 VAC/VDC (non-polarized)

Detection method

Simultaneous breaking of 2 beams

Response time*

50~700 ms (variable)

Alarm output

NO/NC relay, 1A@120VAC, minimum 1 sec.

Tamper output (Tx & Rx)

N.C. switch, 1A@120VAC

Alarm LED (receiver)

Red LED - ON: When transmitter and receiver are not aligned or when
beam is broken.

Signal LED (receiver)

Yellow LED - ON: When receiver's signal is weak or when beam is
broken.

Power LED (Tx & Rx)

Green LED ON: Indicates connected to power

Laser wavelength

650nm

Laser output power

≤

5mW

Alignment angle

Horizontal: ±90°, Vertical: ±5°

Operating temperature

-13°~131° F (-25°~55° C)

Weight 2.5-lb

(1.1kg)

Case PC

Resin

*Factory default is 50ms

Fig. 11:
Adjusting the
Response Time

300ms

50ms 700ms

IMPORTANT

: Note that the response time is set at the factory to the shortest time (50ms).

After installation is complete please adjust to best suit the site situation.

Содержание SLI Enforcer E-960-D190Q













Результаты поиска

Содержание SLI Enforcer E-960-D190Q

Отзывы:

Похожие инструкции для SLI Enforcer E-960-D190Q

Бренды по названию

Популярные бренды

SECO-LARM SLI Enforcer E-960-D190Q, Руководство пользователя

Результаты поиска

Содержание SLI Enforcer E-960-D190Q

Отзывы:

Похожие инструкции для SLI Enforcer E-960-D190Q

Бренды по названию

Популярные бренды