Seametrics FT430 Скачать руководство пользователя страница 6

FT430/440/450 INSTRUCTIONS

Seametrics • 253.872.0284 

Page 6 

seametrics.com

INSTALLATION

Meter Mount.

 If the FT430/440/450 indicator was ordered 

as a meter mount model, the housing is already mounted 

directly to the flow sensor and needs no further installation.

An FT430/440 module can be converted from a wall-mount 

to an IP meter-mount unit using the mounting kit (contact 

distributor) that includes a lower housing and associated 

hardware and installs as follows: 

1. 

Remove the strain relief through which the flow 

sensor cable runs. 

2.  Cut the cable to about 6” in length. Carefully strip 

the cable jacket to expose the three colored wires 

(red, white, and black) inside. 

3.  Route the wires through the threaded connector 

pre-installed in the bottom of the housing. 

4.  Start the threaded connector into the female thread 

on the top of the flow sensor. Be sure to match the 

oblong shape on the bottom of the housing to the 

depression on the top of the flow sensor.

5.  Using an ordinary screwdriver inserted in one side 

of the slot (see drawing), tighten the screw as much 

as possible.

6. 

Strip the wire ends, make the connections to the 

indicator as shown in Connections Diagrams, and 

then use the cover screws to attach the indicator to 

the top of the housing.

Wall Mount. 

To mount an FT430/440/450 indicator to 

the  wall,  hold  the  unit  in  the  desired  position,  mark  the 

holes in the mounting feet, drill and mount with screws. 

A meter-mounted indicator can be converted to a wall 

mount using an adapter mounting kit.  Contact distributor 

for information.
Wall mount housings for FT units are supplied with 3 cord 

grips of different sizes.  Be sure to use the appropriate sized 

cord grip for your cable or cables and to assure any unused 

cord grips are well sealed with a properly sized plug (these 

plugs will come in the cord grips that are supplied with the 

wall mount housing when shipped from the factory.)  There 

will be a properly sized cord grip for any cable supplied by 

Seametrics.

Sensor Wires

Sensor Wires

Meter Mount

Содержание FT430

















Отзывы: