Note:
Maintenance and repair must only be carried out by a qualified person. Contact your Sealey dealer for details.
7.1.
Always keep the press clean, dry and lubricate all moving parts at regular intervals.
7.2.
When not in use always store in a dry location with the piston retracted.
7.3.
Should you need to check or replace oil ensure piston is fully retracted. Remove the oil reservoir filler plug (47) and top up using Sealey
hydraulic jack oil.
DO NOT
use brake fluid. Contact your local Sealey dealer for details. After filling purge the system to remove any air.
IMPORTANT:
NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE PRESS.
Owing to their size and weight, hydraulic products should ideally be repaired by local service agents. We have service / repair
agents in most
parts of the UK. Before returning your product please call our technical helpline on
01284 757505
for advice and troubleshooting guidance.
If the jack is under guarantee please contact your stockist
.
De-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the
product and the oil according to local regulations.
5.1.
Securely attach the press to a flat, firm, level surface taking into account clearance for working pieces.
DANGER! The press is top heavy
. If it requires moving after assembly or for relocation, use suitable slings around the top crossbeam,
or lift direct with a forklift with the forks located under the top crossbeam.
DO NOT
use a pallet truck.
5.2.
Purge hydraulic system before operating the press.
The hydraulic system may require purging in order to eliminate any air that may have built up during transit. Check the oil level and top
up if required, open the release valve by turning anti-clockwise and pump the handle several times. Repeat if necessary.
DANGER!
Press is purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always
ensure the workpiece is secured on the table to ensure loads that flex will not suddenly “give” causing danger to operator or damage to
component. Ensure you have read and understood chapter 1 safety instructions.
6.1.
Check that the release valve on the hydraulic unit is fully closed, ready for operation.
6.2.
Locate the flat pressing plates or the v-blocks on to the bed frame, push down the locating pins to ensure the plates do not slip. Place
workpiece onto the plates and position the head of the hydraulic unit on the centre of the workpiece using an appropriate extension.
Note:
Care must be taken to ensure the plates do not fall from the bed frame.
WARNING!
DO NOT
apply off centre loads.
6.3.
When work is complete turn the release valve anti-clockwise to release the pressure and the piston and the ram head will retract
automatically.
Note:
Always keep the piston retracted after use.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
5. INSTALLATION
7. MAINTENANCE
6. OPERATION
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Original Language Version
YK209F.V2 Issue: 4(L) - 09/05/17
© Jack Sealey Limited
