background image

Refer to

instruction 

manual

Wear 

protective

footwear

Beware 

crushing of 

hands

Wear eye

protection

 

Steel frame construction with hydraulic pump unit. Sliding hydraulic ram assembly    

 

gives 176mm of lateral travel for off-centre pressing applications. Frame head fitted  

 

with ram pressure gauge. Supplied with flat pressing plate/V-blocks.

1.1 

GENERAL SAFETY

  Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.

 

Maintain the

 

press in good condition (use an authorised service agent).

  Replace or repair damaged parts. 

Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.

  Keep the press clean for best and safest performance.

  Locate the press in a suitable working area for its function, keep area clean, tidy, free from unrelated materials and ensure there is 

  adequate lighting.

  Ensure the workpiece is correctly secured before operating the press.

 

WARNING! 

Always wear approved eye or face protection when operating the press. 

  Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair.

  Keep hands and body clear of the work table when operating the press.

 

Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip steel toe-capped shoes/boots.

  Keep children and unauthorised persons away from the working area.

 

DO NOT

 operate the press if any parts are missing as this may cause failure or possible personal injury.

 

DO NOT

 use to compress springs or any other item that could disengage and cause a potential hazard.

 

DO NOT

 stand directly in front of the loaded press and never leave a loaded press unattended.

 

DO NOT

 force the press to achieve a task it was not designed to perform.

 

DO NOT

 make any modifications to the press.

 

DO NOT

 adjust or tamper with the safety valve.

 

DO NOT

 exceed the rated capacity of the press.

 

DO NOT

 apply off centre loads.

 

DO NOT

 allow the workpiece or the arbor plates to fall from the press working bench.

 

DO NOT

 get the press wet or use in damp or wet locations or areas where there is condensation.

 

DO NOT

 operate the press when you are tired, under the influence of alcohol, drugs or intoxicating medication.

  When not in use release pressure from the pump and clean the press. Stand or store the arbors in a safe location.

  

WARNING! Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard be              

     placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly. 

 

  

WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that  

 

  may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this  

 

  product, but must be applied by the operator.

 

DANGER! The press is top heavy

. If it requires moving after assembly or for relocation, use suitable slings around the top crossbeam, or  

     lift direct with a forklift with the forks located under the top crossbeam. 

DO NOT

 use a pallet truck.

INSTRUCTIONS FOR: 

HYDRAULIC PRESS 20TONNE FLOOR TYPE

MODEL No

YK209F.V2

Model No:  . . . . . . . . . . .YK209F

Capacity:  .  .  .  .  .  .  .  .  .  .  .  .20tonne

Ram Stroke:. . . . . . . . . . .180mm

*Ram Mandrel Diameter:  .   .   .   .50mm

Lateral Ram Travel: . . . . . . .176mm

Max Height Ram to Table:  . . .912mm

Min Height Ram to Table: . . . .35mm

Table Aperture:   .   .   .   .   .   .   .   .   .155mm

Working Table Depth: . . . . . .175mm

Working Table Width:  .   .   .   .   .   .510mm

Overall Height:  . . . . . . . . .1619mm

Weight:   .   .   .   .   .   .   .   .   .   .   .   .   .105kg

Safety Guard (Optional):  .  .  .  .YKSG20

* Gauge specifies 'ram diameter' is 60mm. This refers to the internal diameter of the ram and 

is correct. It does not refer to the working mandrel diameter.

Original Language Version

YK209F.V2       Issue: 4(L) - 09/05/17

© Jack Sealey Limited

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT 

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL 

INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

  1. SAFETY 

  2. INTRODUCTION

  3. SPECIFICATION

Отзывы: