5.1 Ensure the machine is unplugged from the power supply. Make sure the tank is clean and free from dust and dirt.
5.2 Remove the dust bag and fit a foam filter over the filter basket. Replace the top section onto the container.
5.3 To the same flexible hose as used in dry cleaning fit the desired nozzle.
5.4 Ensure the switch is Off (position 0) before plugging into the power supply.
5.5 Press the switch to On (position I).
Note:
To vacuum large quantities of liquid, from a sink or tank etc, do not immerse the nozzle completely in the liquid, leave a gap at the top
of the nozzle opening to allow an air inflow. The machine is fitted with a float valve which stops the suction action when the tank has reached
its maximum capacity. The user will notice an increase in motor speed. When this happens, turn off the machine, disconnect from power
supply, remove the head from the container and empty the liquid into a suitable receptacle or drain. To continue vacuuming, refit the head and
proceed. After wet vacuuming, turn the machine off and unplug from power supply. Empty the container and clean and dry the inside and
outside before storage.
Remember!
After wet vacuuming the foam filter must be removed and a dust bag must be fitted before dry vacuuming again.
p
p
WARNING! Not designed for liquid storage. Always empty liquids after use and before storing.
6. BLOWING
6.1 Push the large end of the flexible hose into the blow
connection in the top section.
6.2 Ensure the power switch is turned off and plug in the
power supply.
6.3 Switch on the power (position I).
6.4
The unit will now blow through the hose and can be used to
clear obstructions within the pipe.
p
p
WARNING!
If after a few seconds the hose is still blocked turn of the unit and clear the hose manually.
7. MAINTENANCE
7.1.1 GENERAL MAINTENANCE.
7.1.2 Ensure the machine is unplugged from the power supply.
7.1.3 Disconnect the hose from the container.
7.1.4 Undo the clasps and remove motor head from the container.
7.1.5 Clear out any dirt or debris from the container and hose.
7.1.6 Clean the foam filter by washing it in a mild soapy solution.
7.1.7 Check that the telescopic suction tube operates smoothly, and check the power cable to make sure it has not received any damage.
7.2.1 CARTRIDGE FILTER MAINTENANCE.
7.2.2 Handle the filter carefully when cleaning or installing.
7.2.3 Carefully remove the optional cartridge filter (A) and inspect it for damage. A filter that has small holes or tears in it will not perform
efficiently and should be replaced.
7.2.4 To clean a dry filter, tap it inside a waste bin. (B)
7.2.5 Do not use the filter if it becomes wet as the filter will clog quickly and be very difficult to clean. (The cartridge filter is designed for dry
vacuuming only.) Should the filter be inadvertantly wetted it should be rinsed from the inside (B) and allowed to air dry for 24 hours.
7.2.6 To fit a new/cleaned filter slide it over the filter basket (C) and push it fully home (D)
PC200SD & PC300SD - 2 - 161204
8. TROUBLESHOOTING
Cleaner will not operate.
Dust comes from the motor cover.
Reduced efficiency and increased
motor speed/vibration.
No power supply.
Faulty power cable, switch or motor.
Container full of liquid.
Dust bag (or cartridge) missing or damaged.
Dust bag full.
Nozzle, hose or container inlet blocked.
Check supply.
Check and repair or replace faulty item.
Empty container.
Fit or replace dust bag (or cartridge).
Replace dust bag.
Check nozzle, hose and container inlet for blockage.
9. CONSUMABLES
PC200SD Dust Bags (Pack of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Model No. PC200PB5
PC300SD Dust Bags (Pack of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Model No. PC300PB5
Cartridge Filter (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Model No. PC200CF
Foam Filter (Pack of 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Model No. PC200FF10
IMPORTANT! YOU MUST CHANGE THE DUST BAG REGULARLY. IF THE MACHINE IS USED WITHOUT THE SPECIAL BAG THE MOTOR
WILL BURN OUT EVENTUALLY AND YOUR GUARANTEE WILL BE INVALIDATED. ALWAYS KEEP A PACK OF SPARE BAGS HANDY.
Declaration of Conformity
We, the sole importer into the UK, declare that the products listed here are in conformity with the following standards and directives.
The construction files for these products are held by the Manufacturer and may be inspected,
by a national authority, upon request to Jack Sealey Ltd.
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Power Products.
Signed by Mark Sweetman
16th December 2004
WET & DRY VACUUM CLEANERS
Models: PC200SD & PC300SD
98/37/EC Machinery Directive
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
93/68/EEC CE Marking Directive
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
