10tonne straightener kit with variable
tilt
mODEL NO:
DZre92/C.v2
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFetY
warning!
Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
9
Familiarise yourself with product application and limitations, as well as the specific potential hazards peculiar to the straightener.
warning! no part of this unit or any accessory relating to the straightener is designed for lifting loads. it is intended only as a
pulling device and must be used as such with care.
warning!
Disconnect the straightener from the hydraulic pump before servicing or performing any maintenance on the unit.
9
maintain straightener in good order. Replace/repair with
genuine parts only. Non genuine parts may be dangerous and will invalidate the
warranty.
9
Use qualified person to lubricate and maintain the hydraulic pump.
Do not
use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil
only.
9
Keep the straightener clean for best and safest performance.
warning!
Use straightener on level & solid ground, preferably concrete.
Avoid tarmacadam since the equipment may sink into the
surface.
9
Keep area clean & tidy and free from unrelated materials. Ensure there is adequate lighting.
warning!
Ensure you know how much load you are pulling. Never exceed the maximum pulling capacity.
9
Use in conjunction with Sealey hydraulic pump, chains, hooks, etc only.
Do not
use pumps or accessories other than those supplied
with
kit, or contact your local agent for details of Sealey hydraulic pumps and pulling accessories. Non-genuine items may damage unit and void
warranty.
9
Ensure there is positive engagement of straightener chains, claws, hooks, links etc to the chassis or vehicle body before pulling.
9
Place tarpaulin or heavy cover over chains to minimise any backlash should chains or accessory fail.
9
Should jacks be employed in the operation, ensure they are of the appropriate type and capacity, are in good condition and that you follow
any instructions relating to the jack. Also ensure correct stress supports are used between the jack and jacking surfaces.
9
maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
warning! keep your hands, body and clothing away from the chassis and straightener accessories in use.
take any necessary
precautions to protect your personal safety whilst using the straightener.
9
Ensure the hydraulic hose is not bent or kinked.
9
Keep non essential persons away from the operating area. Be aware of the location of other persons assisting you.
9
When releasing tension from the load be sure to undo the hydraulic valve VERY slowly.
8
Do not
operate the straightener if any parts are damaged or missing as this may cause failure or possible personal injury.
warning! Do not use straightener as a lifting device of any type.
Do not use for any purpose other than for which it is designed.
8
Do not
pull chains or cables over or around sharp corners.
8
Do not
heat chains or accessories as this may weaken them.
8
Do not
bolt links together.
2. introDuCtion
One of the biggest selling chassis repair systems in the UK with proven performance over the last 20 years. Variable position upright allows six
pre-set angles of pull plus a seventh upright position. Supplied as standard with SuperSnap® manual hydraulic pump and ram.
iMPortant:
Only fully trained and qualified perons should use this equipment.
3. Contents
Chassis Frame, SuperSnap® Hydraulic Pump & Ram, Pull Clamp (x2), Sill Clamp (x2), Chain (x2), Chain Hook (x2), Carriage Anchorage Tube,
Tube Stand (x2).
Refer to
instruction
manual
Wear head
protection
Wear
protective
gloves
Original Language Version
© Jack Sealey Limited
DZRE92/C.V2 | Issue:3 (2) 29/10/19
