SEAL 80Pro Скачать руководство пользователя страница 28

Страница: 28 / 48

User Manual 80

Pro

5.1.4 Error indications

When an error is detected, one or more LED’s are flashing and any rotation will stop.

Power indicator flashing;

Machine is in stand-by mode. The power is on and the optical safety device is active.
Press the control ON/OFF button to activate the machine.

Forward indication flashing;

Motor overload.
Press the stop button and check the material flow and the tension setting of the unwind
shafts.

Reverse indicator flashing;

Motor overload.
Press the stop button and check the material flow and the tension setting of the wind-up
shafts.

Forward and reverse indicator flashing;

System error.
Disconnect and then reconnect the power. If the error persists, contact your service
organization.

All four pressure indication LED’s are flashing;

Pressure too high or nip setting too narrow.
The LED’s start flashing at 10% overload. When the pressure exceeds a 20% overload an
audible signal is generated. Increase the nip to lower the pressure.

Содержание 80Pro

















































Результаты поиска

Содержание 80Pro

Отзывы:

Похожие инструкции для 80Pro

Бренды по названию

Популярные бренды

SEAL 80Pro, Руководство пользователя

Результаты поиска

Содержание 80Pro

Отзывы:

Похожие инструкции для 80Pro

Бренды по названию

Популярные бренды