Seagate ST31051 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 200

background image

102 Product Manual - Disc Drive SCSI-2/SCSI-3 Interface (Vol. 2; Ver. 2), Rev. E
_____________________________________________________________________________________

Translate Address Page - Send Diagnostic

The translate address page allows the initiator to translate a logical block address into a physical sector
address or a physical sector into a logical block address. The address to be translated is passed to the disc
drive with Send Diagnostic command and the results are returned to the initiator during the data in phase
following the Receive Diagnostic Results command. The format of the translate address page - Send Diag-
nostic is shown in Table 5.1.1-17. The translated address is returned in the translate address page returned
after the Receive Diagnostic Results Command (see Table 5.1.1-11).

Table 5.1.1-17. Translate Address Page - Send Diagnostic

Bit

7

6

5

4

3

2

1

0

Byte(s)

0

Page Code (40h)

1

Reserved

2

(MSB)

Page Length (000Ah)

3

(LSB)

4

Reserved

Supplied Format [1]

5

Reserved

Translate Format [2]

6
:

Address To Translate [3]

13

Notes.

[1] The Supplied Format field specifies the format of the address to translate field. The valid values for this

field are 000 for logical block address format or 101 for physical sector address format. If the disc drive
does not support the requested format it shall terminate the Send Diagnostic command with Check
Condition status. The sense key shall be set to Illegal Request and an additional sense code shall be set
to Invalid Field In Parameter List.

[2] The Translate Format field specifies the format to which the initiator would like the address to be trans-

lated. The valid values for this field are 000 for logical block address format or 101 for physical sector
address format. The Translate Format field must be different than the Supplied Format Field. If the disc
drive does not support the requested format it shall terminate the command with Check Condition status.
The sense key shall be set to Illegal Request and an additional sense code shall be set to Invalid Field In
Parameter List.

[3] The Address to Translate field contains a single address the initiator is requesting the disc drive to

translate. The format of this field is defined by the Supplied Format Field. The supported formats are
shown in Table 5.1.1-14a and Table 5.1.1-14b.

For systems which support disconnection, the disc drive will disconnect while executing this command.

«
...
110
111
112
113
114
...
»

Содержание ST31051









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ST31051

Бренд: Seagate Страницы: 28

Terascale ST4000NC000

Бренд: Seagate Страницы: 37

Бренд: Supero Страницы: 112

Fairmont Garden Shed

Бренд: YardCraft Страницы: 29

Бренд: QNAP Страницы: 7

Бренд: Keter Страницы: 28

B. spaces Tidy Toybox

Бренд: Maison Battat Страницы: 2

Бренд: Plasmon Страницы: 33

Бренд: Acard Страницы: 43

Бренд: Quantum Страницы: 45

SmartStore SM2520

Бренд: Riverlea Страницы: 16

Бренд: iodd Страницы: 16

Бренд: ABSCO SHEDS Страницы: 21

Бренд: Seagate Страницы: 2

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 2

HD161HJ - SpinPoint S166 160 GB Hard Drive

Бренд: Samsung Страницы: 2

HD321KJ - SpinPoint T166 320 GB Hard Drive

Бренд: Samsung Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды