manualshive.com logo in svg

Seagate ST31051, Руководство по эксплуатации продукта


Поделиться
Скачать
background image

Product Manual - Disc Drive SCSI-2/SCSI-3 Interface (Vol. 2; Ver. 2), Rev. E                                     167
_____________________________________________________________________________________

continued from previous page

[5] The active notch field indicates the notch to which this and subsequent Mode Select and Mode Sense

commands shall refer, until the active notch is changed by a later Mode Select command. The value of
the active notch shall be greater than or equal to 0 and less than or equal to the maximum number of
notches. A active notch value of zero indicates that this and subsequent Mode Select and Mode Sense
commands refer to the parameters that apply across all notches.

[6] The starting boundary field indicates the beginning of the active notch or, if the active notch is zero, the

beginning boundary of the drive. If the LPN bit is one, then the four bytes represent a logical block
address. If the LPN bit is zero, then the three most significant bytes shall represent the cylinder number
and the least significant byte shall represent the head number. When used with the Mode Select com-
mand this field is ignored.

[7] The ending boundary field indicates the ending of the active notch or, if the active notch is zero, the

ending of the drive. If the LPN bit is one, then the four bytes represent logical block address. If the LPN
bit is zero, then the three most significant bytes shall represent the cylinder number and the least signifi-
cant byte shall represent the head number. When used with the Mode Select command this field is
ignored.

Each notch shall span a set of consecutive logical blocks on the drive, the notches shall not overlap, and
no logical block shall be excluded from a notch.

[8] The pages notched field is a bit map of the mode page codes that indicates which pages contain param-

eters that may be different for different notches. The most significant bit of this field corresponds to page
code 3Fh and the least significant bit corresponds to page code 00h. If a bit is one, then the correspond-
ing mode page contains parameters that may be different for different notches. If a bit is zero, then the
corresponding mode page contains parameters that are constant for all notches.

[9] These values are not changeable.

[10] See drive Product Manual Mode Sense Data section for changeable values.

Содержание ST31051









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ST31051

NEC S2500 User Manual preview
S2500
Бренд: NEC Страницы: 106
Tandberg Data StorageLoader DLT VS160 Quick Installation Manual preview
StorageLoader DLT VS160
Бренд: Tandberg Data Страницы: 13
Tandberg Data StorageLoader DLT VS160 Installation And Operation Manual preview
StorageLoader DLT VS160
Бренд: Tandberg Data Страницы: 46
Tandberg Data StorageLibrary LTO-3 SCSI Quick Start Manual preview
StorageLibrary LTO-3 SCSI
Бренд: Tandberg Data Страницы: 2
Tandberg Data SDLT220-320 INTEGRATION Product Manual preview
SDLT220-320 INTEGRATION
Бренд: Tandberg Data Страницы: 142
Tandberg Data RDX QuikStor Quick Start preview
RDX QuikStor
Бренд: Tandberg Data Страницы: 3
Tandberg Data Magnum 224 Instructions Manual preview
Magnum 224
Бренд: Tandberg Data Страницы: 12
HPE G2 R8000 3U WW ERM Product End-Of-Life Disassembly Instructions preview
G2 R8000 3U WW ERM
Бренд: HPE Страницы: 3
Forest garden OPATSFP Quick Start Manual preview
OPATSFP
Бренд: Forest garden Страницы: 4
GARANT 92 0051 1500 User Manual preview
92 0051 1500
Бренд: GARANT Страницы: 40
Arrow Storage Products HDVAS107 Owner'S Manual & Assembly Manual preview
HDVAS107
Бренд: Arrow Storage Products Страницы: 44
IBM 1 GB Microdrive Storage Card Quick Installation Manual preview
1 GB Microdrive Storage Card
Бренд: IBM Страницы: 2
Microdia MMCPLUS Operating Manual preview
MMCPLUS
Бренд: Microdia Страницы: 1
Backyard YardLine ASTON Assembly Manual preview
YardLine ASTON
Бренд: Backyard Страницы: 60
Excalibur Do It Yourself Workbench EI-PT1013 User Manual preview
Do It Yourself Workbench EI-PT1013
Бренд: Excalibur Страницы: 2
Silverline 666247 Quick Start Manual preview
666247
Бренд: Silverline Страницы: 2
HermanMiller Meridian Disassembly For Recycling preview
Meridian
Бренд: HermanMiller Страницы: 5
Würth ORSY Flex 350 Operating Instructions Manual preview
ORSY Flex 350
Бренд: Würth Страницы: 196

Бренды по названию

Популярные бренды

Загрузить еще бренды