SeaDoo Rotax 1503 4-Tec 2005 страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 124

background image

Section 01 ENGINES (1503 4-TEC)

Subsection 02 (INTAKE MANIFOLD AND SUPERCHARGER)

Mount supercharger housing half (engine side) on
support plate (P/N 529 035 947).

529035947

Apply Loctite 243 (P/N 293 800 060) on retaining
disc and install it in supercharger housing half by
using the 4-pin socket (P/N 529 035 948). Torque
to 30 N•m (22 lbf•ft).

529035948

NOTE:

If a new disc is installed, do not use any

Loctite, threadlocker is already applied.

1

F00B2IA

2

1. Retaining disc
2. 4-pin socket

To press supercharger shaft in housing half (en-
gine side), properly support bearing, using support
plate (P/N 529 035 947) and bearing support/push-
er (P/N 529 035 950) under supercharger housing
half.

529035950

3

F00B2GA

1

2

1. Support plate
2. Bearing support/pusher
3. Protrusion here

CAUTION:

Before pressing in the supercharg-

er shaft, be sure to properly support the inner
race of ball bearing in supercharger housing
half with the recommended tool. This way, the
installation pressure will be applied to the inner
race and will not be transmitted to the bearing
balls which would otherwise shorten the bear-
ing life.

Apply heat outside of the housing with a heat gun
to expand its diameter prior to inserting the shaft.
Ensure there is no O-ring on the housing half prior
to heating.

Apply engine oil on supercharger shaft. Press
shaft with distance sleeve together in supercharg-
er housing half.

SMR2005-033

23

www.SeaDooManuals.net

«
...
31
32
33
34
35
...
»

Содержание Rotax 1503 4-Tec 2005





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Rotax 1503 4-Tec 2005

MWM INTERNATIONAL MaxxForce 9.3P

Бренд: Navistar Страницы: 126

BAUDOUIN PowerKit 16M33 Series

Бренд: WEICHAI Страницы: 142

Бренд: Beckhoff Страницы: 31

BCS 7700 Series

Бренд: Honeywell Страницы: 6

Бренд: Honeywell Страницы: 10

Modutrol IV Motors Series 90

Бренд: Honeywell Страницы: 12

Modutrol IV M9164A 1013

Бренд: Honeywell Страницы: 16

Modutrol IV 41 Series

Бренд: Honeywell Страницы: 12

Бренд: Honeywell Страницы: 40

Modutrol IV 72 Series

Бренд: Honeywell Страницы: 12

Бренд: Honeywell Страницы: 12

Modutrol IV M9175D 1014

Бренд: Honeywell Страницы: 16

Modutrol IV M945F

Бренд: Honeywell Страницы: 12

Modutrol IV M6284A1030

Бренд: Honeywell Страницы: 12

Modutrol IV M72 Series

Бренд: Honeywell Страницы: 12

Бренд: Honeywell Страницы: 16

Бренд: Honeywell Страницы: 28

Бренд: Honeywell Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды