SeaDoo Rotax 1503 4-Tec 2005 страница 10 Скачать руководство пользователя

Страница: 10 / 124

INTRODUCTION

1
2

Section 06 FUEL SYSTEM

Subsection 03 (CARBURETORS)

Diaphragm

XP Model Only

CARBURETOR REMOVAL

Inspect parts for corrosion dammage (shaft, butterfly,

spring screw, check valve housing, etc.).

PUMP DIAPHRAGM LEAK TEST

TYPICAL

To remove carburetors from engine, proceed as fol-

lows:
Remove air vent tube support.
Unlock retaining slides holding air intake silencer base.

Remove air intake silencer base from watercraft.
Remove screws holding flame arrester base support

to cylinder head cover.
Unscrew base retaining screws then remove base from

carburetors and move to front of watercraft.
Turn the valve to OFF position.

NOTE:

For fuel line removal, use pliers (P/N 295

000 054).
Disconnect pulse line from fuel pump.
Disconnect fuel fuel supply line from fuel pump.
Disconnect fuel return line.
Disconnect oil injection pump cable, throttle cable and

choke cable.

Remove screws

no. 6

and lock washers

no. 7

retaining

carburetors.

All Others Models

Remove 4 bolts

no. 8

and lock washers

no. 12

from

rotary valve cover then move carburetors and rotary

valve cover on top of engine.

NOTE:

When removing rotary valve cover , pay

attention that the rotary valve stay in place, other-wise

it must be timed.
Remove carburetors from intake manifold.
Disconnect fuel bypass line between carburetors (twin

carburetors).
Remove carburetor(s) from rotary valve cover.

DISASSEMBLY AND INSPECTION

Using a suitable pump gauge tester, perform the fol-

lowing test proceeding as follows:
- Install pump gauge tester (P/N 295 000 083) on pulse

nipple.
- Pump tester until it reaches 28 kPa (4 PSI).

Diaphragm must stand pressure for 10 seconds. If

pressure drops, replace diaphragm.

F01F0XB

TYPICAL PAGE

Sub-title with part

name(s) from

exploded view.

TYPICAL mention

indicates a general

view which does not

represent full detail.

Sub-sub-title in this

case indicates that

particular procedure

for XP is finished, so

from this point, all

others models are

concerned.

Title in italic indicates a

particular procedure

concerning a model.

Service tool to be

used to perform a

certain procedure.

Title indicates main

procedure to be

carried-out.

Sub-sub-title in

capital indicates a

particular testing,

adjustment or

repair procedure.

Illustration

always follows

text it is

pertained to.

Numbered step are

used to give a

sequence to be

perfomed.

Numbers are used

for description of

components.

Letters are used for

any measures.

Bold numbers in the

text refer to the parts

shown in the exploded

view at the beginning

of the subsection.

F01A0BT

smr2005-002

VII

www.SeaDooManuals.net

Содержание Rotax 1503 4-Tec 2005





























































































































Результаты поиска

Содержание Rotax 1503 4-Tec 2005

Отзывы:

Похожие инструкции для Rotax 1503 4-Tec 2005

Бренды по названию

Популярные бренды

SeaDoo Rotax 1503 4-Tec 2005, Руководство по ремонту двигателя

Результаты поиска

Содержание Rotax 1503 4-Tec 2005

Отзывы:

Похожие инструкции для Rotax 1503 4-Tec 2005

Бренды по названию

Популярные бренды