background image

Battery Use

5.  If  the  SEASCOOTER

™ 

sinks,  remove  rocks  until  it  is 

neutrally buoyant.

      If  the  SEASCOOTER

™ 

is  still  positively  buoyant  repeat 

step 3, until it is neutrally buoyant.

8

9

Fig.5

CAUTION

If  the  SEASCOOTER

  is  later  used  for  swimming  or 

snorkeling  be  sure  to  remove  the  weight  from  the 
Buoyancy Chamber so the SEA-DOO

®

 SEASCOOTER

 

VS Supercharged has positive buoyancy.

CAUTION

• The  Battery  Housing  should  always  be  ventilated 

during charging to allow potentially explosive gasses 
to  dissipate.  Before  removing/attaching  any  battery 
cables  always  allow  two  minutes  for  any  gasses  to 
dissipate.

•  ALWAYS  plug  the  charger  jack  into  the  charging 

socket  first  and  then  plug  into  the  mains.  When 
charging  is  complete,  unplug  the  charger  from  the 
mains first and then from the charging socket.

• ALWAYS ensure the charger is DRY before plugging it 

into a live socket.

•  NEVER  place  the  battery  in  a  sealed  container  when 

charging.

• Never charge battery near water.

•  If  in  doubt  of  the  state  of  the  battery,  recharge  it 

until the indicator on the battery charger indicates a 
full charge.

•  ALWAYS  charge  battery  in  a  well-ventilated  place 

where unit is out of reach of children.

•  ALWAYS  ensure  the  unit  is  dried  thoroughly  before 

opening the Nose Cone for charging or changing the 
battery.

Содержание ZS5A














Отзывы: