Sea-doo GS 5644 Скачать руководство пользователя страница 86

Страница: 86 / 107

Engine Lacks Acceleration or Power

Watercraft Can Not Reach Top Speed

Abnormal Noise From Propulsion System

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

• Weak spark

Refer to engine MISFIRES, RUNS
IRREGULARLY.

• Incorrect fuel mixture

(carburetor-equipped
models)

Refer to engine MISFIRES, RUNS
IRREGULARLY.

• Water in fuel or injection

oil.

Siphon and replace.

Overheated engine.

• See engine OVERHEATS.

• Clogged fuel injectors

(RFI models)

Refer to an authorized Sea-Doo
dealer.

• Low fuel pressure

(RFI models)

Refer to an authorized Sea-Doo
dealer.

• Stuck RAVE valves

(if so equipped)

Refer to an authorized Sea-Doo
dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Cavitation.

• Jet pump water intake

clogged.

Clean.

• Damaged impeller.

Replace. Refer to an authorized
Sea-Doo dealer.

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Cavitation.

• Weeds or debris jammed

around impeller.

Clean and check for damage.

• Damaged impeller shaft

or drive shaft.

Refer to an authorized Sea-Doo
dealer.

smo2000-002a.book Page 84 Tuesday, September 28, 1999 12:00 PM

www.SeaDooManuals.net

Содержание GS 5644












































































































Результаты поиска

Содержание GS 5644

Отзывы:

Бренды по названию

Популярные бренды

Sea-doo GS 5644, Руководство оператора

Результаты поиска

Содержание GS 5644

Отзывы:

Бренды по названию

Популярные бренды