Sea-doo GS 5644 Скачать руководство пользователя страница 39

Страница: 39 / 107

26) Rear Vent Grills

(if so equipped)

Allows air to get in or out depending
on engine operation.

CAUTION:

If grills are kept below

water level for a long period (e.g.:
when boarding 2 passengers) water
will enter the bilge.

27) Seat Strap

The seat strap provides a handhold to
assist boarding and is used as a hand-
hold for the passenger.

28) Seat Latch

Removing the seat allows access to
the engine compartment and to oil res-
ervoir cap/dipstick.

The seat latch is located at the rear end
and underneath the seat.

TYPICAL

1. Seat latch

To remove seat, pull the latch lever up-
ward and hold. Lift and pull the seat
rearward.

NOTE:

On the

GTI, GTX and GTX RFI

models

, it is necessary to remove the

rear seat first and repeat the same pro-
cedure to remove the front portion of
the seat.

Engine Compartment

This is where the mechanical, electri-
cal and fuel/oil systems are located.

When reinstalling the seat, insert seat
front tab into body hook (for each por-
tion of the seat on the

GTI, GTX and

GTX RFI models

GTX MODELS

1. Insert this tab in hook
2. Hook

ALL MODELS EXCEPT GTX

1. Insert this tab in hook
2. Hook

F01L8XZ



WARNING

When starting or operating the en-
gine, do not touch any electrical
part. Never leave any object, rag,
tool, etc., in the engine compart-
ment or in the bilge.

F01L92Y

1 2

F06L12Y

smo2000-002a.book Page 37 Tuesday, September 28, 1999 12:00 PM

www.SeaDooManuals.net

Содержание GS 5644












































































































Результаты поиска

Содержание GS 5644

Отзывы:

Похожие инструкции для GS 5644

Бренды по названию

Популярные бренды

Sea-doo GS 5644, Руководство оператора

Результаты поиска

Содержание GS 5644

Отзывы:

Похожие инструкции для GS 5644

Бренды по названию

Популярные бренды