Sea-doo GS 5644 Скачать руководство пользователя страница 59

Страница: 59 / 107

NOTE:

This prevents water from di-

rectly exiting cooling system.

GTS MODELS

1. Fitting spigot
2. Coupler hose
3. Hose pincher

Attach other end of coupler hose to a
garden hose.

Do not open water tap

yet.

Other Models

Connect a garden hose to connector
located at the rear of watercraft on jet
pump support.

NOTE:

A quick connect adapter can be

used (P/N 295 500 473). No hose
pincher is required to flush engine.

TYPICAL

1. Hose adapter
2. Quick connect adapter (not mandatory)
3. Garden hose

NOTE:

The quick connect adapter may

be supplied with

some models

. It has

to be removed if you do not use a quick
connect adapter on your garden hose.

Flushing

All Models

To flush cooling system, start the en-
gine

then

immediately open the water

tap.

CAUTION:

Never flush a hot engine.

Always start the engine before open-
ing the water tap. Open water tap
immediately after engine is started
to prevent overheating.

Run the engine about 3 minutes at a
fast idle around 3500 RPM.

CAUTION:

Never run engine longer

than 5 minutes. Drive line seal has no
cooling when watercraft is out of wa-
ter.

Lubrication

Spray BOMBARDIER LUBE lubricant
or equivalent, through hole of air intake
silencer keeping engine at fast idle
during one minute.

GS, GTS, GTI, GTX RFI AND GSX RFI
MODELS

1. Air intake silencer
2. Pull plug
3. Spray BOMBARDIER LUBE here

F02E03Y

F07E01Y



WARNING

Do not touch any electrical parts or
jet pump area when engine is run-
ning.

F01F25Y

smo2000-002a.book Page 57 Tuesday, September 28, 1999 12:00 PM

www.SeaDooManuals.net

Содержание GS 5644












































































































Результаты поиска

Содержание GS 5644

Отзывы:

Sea-doo GS 5644, Руководство оператора, Страница: 59 / 107

Результаты поиска

Содержание GS 5644

Отзывы: