Sea-doo 1997 GS страница 79 Скачать руководство пользователя | Manualshive

Страница: 79 / 105

background image

77

If defective, replace the fuse by one of
the same rating.

Properly close cover of each electrical
box, making sure each seal is well po-
sitioned.

General Inspection and
Care

Inspection

Check engine compartment for any
damage and fuel/oil injection systems
for leaks. Ensure all hose clamps are
properly secured and no hose is
cracked, kinked or presenting any oth-
er damage.

Inspect muffler, battery and fuel/oil
reservoir fastening devices. Check
electrical connections for corrosion
and tightness.

Inspect hull and jet pump water intake
grate for damage. Replace or have
damaged parts repaired. It is recom-
mended that an authorized dealer an-
nually inspect the hull condition.

Care

Twice a year, the bilge should be
cleaned with hot water and detergent
or bilge cleaner to remove any possi-
ble fuel/oil/electrolyte deposits and
mildew.

Occasionally, wash the body with wa-
ter and soap (only use mild detergent).
Remove any marine organisms from
engine and/or hull. Apply non-abrasive
wax such as silicone wax.

-

CAUTION

Do not use a higher rated fuse as
this can cause severe damage.
Refer to SPECIFICATIONS section
for recommended fuse rating. If a
fuse is regularly burnt, refer to an
authorized dealer.

◆

WARNING

If any water is found in the elec-
trical box(es), immediately refer
to an authorized dealer before
operating the watercraft.

◆

WARNING

If any gasoline leak or odor is
found, do not start the engine.
Have the watercraft serviced by
an authorized dealer.

-

CAUTION

Never clean apparent fiberglass
and plastic parts with strong de-
tergent, degreasing agent, paint
thinner, acetone, etc.

smo9701a.bk : smo9701b.fm5 Page 77 Monday, November 3, 1997 9:54 AM

www.SeaDooManuals.net

«
...
77
78
79
80
81
...
»

Содержание 1997 GS










































































































Отзывы:

Нет отзывов

Похожие инструкции для 1997 GS

Бренд: MACGREGOR Страницы: 22

Бренд: Boston Whaler Страницы: 161

Бренд: Corsiva Yachting Страницы: 33

Бренд: Corsiva Yachting Страницы: 37

Бренд: Oxxean Страницы: 37

Бренд: SEALVER Страницы: 16

Бренд: Bootzeil Страницы: 38

Бренд: BENETEAU Страницы: 18

Бренд: Supra Страницы: 89

Бренд: Supra Страницы: 88

Бренд: Sailfish Страницы: 43

BENETEAU OCEANIS 400

Бренд: Darfin Yachts Страницы: 82

SUN ODYSSEY 45DS

Бренд: Jeanneau Страницы: 146

Бренд: ISLAND PACKET Страницы: 8

Бренд: Quicksilver Страницы: 87

WAVE 275 Roll Up

Бренд: Zodiac Страницы: 18

Бренд: GALA Страницы: 12

Бренд: Gumotex Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды