Sea-doo 1997 GS страница 83 Скачать руководство пользователя | Manualshive

Страница: 83 / 105

background image

81

Remove temporary hose and recon-
nect engine water supply hose and
engine water return hose.

Remove hose pincher.

All Models

The following steps should be per-
formed to provide the watercraft en-
hanced protection.

Remove muffler and drain out as
much water as possible. Reinstall
muffler.

OR:

Disconnect one hose from muf-

fler and pour some antifreeze solution
inside muffler. Reconnect hose.

Lubricate the throttle cable with BOM-
BARDIER LUBE lubricant.

NOTE:

A cable luber can be used

on throttle cable end to inject

BOMBARDIER LUBE lubricant.

Clean the bilge with hot water and de-
tergent or with bilge cleaner. Rinse
thoroughly. Lift front end of watercraft
to completely drain bilge. If any repairs
are needed to body or to the hull con-
tact your dealer. For paint touch up to
mechanical parts use Bombardier
spray paint. For small gelcoat repairs,
a Bombardier repair kit is available.
See ACCESSORIES AND SERVICE
PRODUCTS section. Replace dam-
aged labels/decals.

NOTE:

Bilge cleaning should be

done prior to anticorrosion treat-

ment.

Wash the body with soap and water
solution (only use mild detergent).
Rinse thoroughly with fresh water. Re-
move marine organisms from the hull.
Apply a nonabrasive wax such as sili-
cone wax.

If the watercraft is to be stored out-
side, cover it with an opaque tarpaulin
to prevent sun rays and grime from af-
fecting the plastic components, wa-
tercraft finish as well as preventing
dust accumulation.

The seat should be partially left
o p e n e d d u r i n g s t o r a g e ( e x c e p t
HX/XP). This will avoid engine com-
partment condensation and possible
corrosion.

NOTE:

If the watercraft is stored

outside with seat partially opened

and without a tarpaulin, unscrew the
rear drain plug in order to avoid water
build up in the bilge during rainfall. Tilt
the watercraft to the rear so that wa-
ter can flow out of floorboard.

Pre-Season Preparation

Use the following chart.

Since technical skills and special tools
are required, some operations should
be performed by an authorized dealer.

-

CAUTION

Never clean apparent fiberglass
and plastic parts with strong de-
tergent, degreasing agent, paint
thinner, acetone, etc.

'

'

-

CAUTION

The watercraft must never be left
in water for storage. Never leave
the watercraft stored in direct
sunlight. UV rays will dull finishes.

◆

WARNING

Observe all WARNINGS and
CAUTIONS mentioned through-
out this guide which are pertinent
to the item being checked. When
component conditions seem less
than satisfactory, replace with
genuine BOMBARDIER parts or
approved equivalents.

'

smo9701a.bk : smo9701b.fm5 Page 81 Monday, November 3, 1997 9:54 AM

www.SeaDooManuals.net

«
...
81
82
83
84
85
...
»

Содержание 1997 GS










































































































Отзывы:

Нет отзывов

Похожие инструкции для 1997 GS

WaveRunner GP1300R

Бренд: Yamaha Страницы: 340

WaveRunner GP1300R

Бренд: Yamaha Страницы: 60

WaveRunner GP1200R

Бренд: Yamaha Страницы: 245

Бренд: Yamaha Страницы: 60

Бренд: Yamaha Страницы: 126

Бренд: Yamaha Страницы: 118

Бренд: Spitfire Страницы: 10

Hewes Redfisher 16

Бренд: Maverick Boat Страницы: 23

Бренд: Grand Banks Страницы: 51

Бренд: Ranger boats Страницы: 80

Бренд: GALA Страницы: 10

Бренд: Pelican Страницы: 12

Бренд: Pelican Страницы: 2

Бренд: Point 65 Страницы: 2

Бренд: Point 65 Страницы: 3

Бренд: Point 65 Страницы: 8

Бренд: Nautiraid Страницы: 12

Бренд: Quicksilver Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды