SCS 724 Plus Скачать руководство пользователя страница 7

TB-9098

 Page 7 of 7

© 2020 DESCO INDUSTRIES INC

Employee Owned

SCS 

- 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: 

StaticControl.com

Calibration

Frequency of recalibration should be based on the 

critical nature of those ESD sensitive items handled and 

the risk of failure for the ESD protective equipment and 

materials. In general, SCS recommends that calibration 

be performed annually.
Use the SCS 

770065

 

Verification Tester to perform 

periodic testing (once every 6-12 months) of the 724 

Plus Workstation Monitor. The Verification Tester 

can be used on the shop floor within a few minutes 

virtually eliminating downtime, verifying that the tester is 

operating within tolerances.

Limited Warranty, Warranty Exclusions, Limit 

of Liability and RMA Request Instructions

See the SCS Warranty - 

StaticControl.com/Limited-Warranty.aspx

Figure 10. SCS 

770065

 Verification Tester

Specifications

Power

Power Adapter

100-240VAC

50-60 Hz

Output: 12 VDC @ 1.5 A

Output Plug Polarization: 

Center Positive

Output Plug: 5.5 mm O.D. x 

2.1 mm I.D. x 9.5 mm L

Operator

Wrist Strap

Dual-Wire

Amount Monitored

2

Resistance Limit

1.5 megohms to 10 megohms

Body Voltage Limit

±2.5 VDC

Test Voltage

0.40 V @ open circuit, 

peak-to-peak

Test Accuracy

±10%

Worksurface Mat

Amount Monitored

1

Resistance Limit*

3.7 megohms

Test Accuracy

±10%

General

Alarm

LEDs and buzzer

Alarm Response Time 500 ms

Dimensions 

(Monitor)

0.85" x 2.40" x 2.60"  

(22 mm x 61 mm x 66 mm)

Dimensions 

(Operator Remote)

2.41" x .84" x 1.13"

(61 mm x 21 mm x 29 mm)

Operator Remote 

Cable Length

7 ft. (2.1 m)

Weight 

(Monitor)

0.14 lbs. (64 g)

Weight 

(Operator Remote)

0.07 lbs. (32 g)

Country of Origin

United States of America

*The worksurface must have a conductive layer such 

as Dual Layer Rubber or Dissipative 3-Layer Vinyl with 

conductive buried layers. SCS workstation monitors are 

not recommended for use with homogeneous matting.
ANSI/ESD S20.20 requires the use of a surface 

resistance meter for periodic verification of a 

worksurface's resistance-to-ground (Rtg). Constant 

monitors may not be used as a substitute for this 

requirement.

Содержание 724 Plus








Отзывы: