SCS 724 Plus Скачать руководство пользователя страница 4

TB-9098

 Page 4 of 7

© 2020 DESCO INDUSTRIES INC

Employee Owned

SCS 

- 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: 

StaticControl.com

Installation

724 Plus Workstation Monitor and Dual 

Operator Remote

5.  Route the operator remote cable from the back 

of the 724 Plus Workstation Monitor to the Dual 

Operator Remote. Connect the cable to the back of 

the Dual Operator Remote. 

6.  Insert the tinned termination of the mat monitor cord 

into the mat terminal located on the back of the 724 

Plus Workstation Monitor. Use a small screwdriver 

to secure the wire to the terminal block. 

7.  Route the mat monitor cord from the back of the 

724 Plus Workstation Monitor to the grounded 

worksurface mat. Use the included countersunk 

washer and flat head screw to secure the cord to 

the grounded mat. 

 

NOTE: The worksurface must be connected directly 

to ground without the use of a 1 megohm resistor.  

 

Per ANSI/ESD S6.1 Section 5.2.1 Common Point 

Ground: 

"All of the grounding conductors from each of the 

ESD technical elements (excluding level 2 technical 

elements) used within an EPA shall be terminated at 

the same electrically equivalent point. The common 

point ground may be a terminal strip, bus bar or any 

other convenient configuration that is, within itself, 

electrically continuous to no greater than 1 ohm 

measured from point to point with an ohmmeter as 

specified in paragraph 6.1.1." 

8.  Insert the tinned termination of the ground cord into 

the ground terminal located on the back of the 724 

Plus Workstation Monitor. Use a small screwdriver 

to secure the wire to the terminal block. 

9.  Attach the other end of the ground cord to a ground 

point. The face plate screw of a grounded AC wall 

outlet may provide a convenient connection point. 

10. Connect the power adapter to the power jack 

located on the back of the 724 Plus Workstation 

Monitor. Route the wire from the supply to a nearby 

AC outlet and plug it into the outlet. Make sure the 

voltage and frequency match those listed on the 

power supply. The 724 Plus Workstation Monitor is 

now powered.

Figure 5. Installing the 724 Plus Workstation Monitor and 

Dual Operator Remote

Mat Monitor Cord

724 Plus 

Workstation Monitor

Grounded Worksurface Mat

Power Adapter

Operator 

Remote Cable

Monitor Ground Cord

Dual Operator Remote

Countersunk

Washer

Flat Head 

Screw

1.  Remove the 724 Plus Workstation Monitor and its 

Dual Operator Remote from the carton. 

2.  Determine the mounting location of the 724 Plus 

Workstation Monitor. Its display should be visible to 

the operator(s). Use its enclosure's mounting tabs to 

secure it underneath a shelf or ledge. 

3.  Determine the mounting location of the Dual 

Operator Remote. Its jacks should be accessible 

to operators. Locate it within reach of the included 

operator remote cable. Use its enclosure's 

mounting tabs to secure it underneath a table top or 

equipment. 

4.  Connect the included operator remote cable to the 

dual operator remote connector located on the back 

of the 724 Plus Workstation Monitor. 

Содержание 724 Plus








Отзывы: