background image

1

IN

 AU

STRAL

IA

PR

OU

DLY BUILT

Continued Over.../

The motor controller for the MasterFit range of projection screens is housed in an insulated
box and is packaged with a 1.2M IEC mains flex with moulded 3 pin plug and 240 volt output
to motor is supplied with a 4 pin WAGO connector with a 4M long 4 core flex allowing
placement flexibility.

Thank you for purchasing a Screen Technics Projection Screen, please 
ensure that you read the following instructions fully before installing this 
product.

GENERAL INSTRUCTIONS 

INSTRUCTIONS - 

MASTERFIT IP 

A, A+, B, B+, C, C+ Projection Screen

A. CONTACT CLOSE INPUT

• 

No voltage, dry contact input

• 

Requires momentary contact only

• 

Contact is closed and opened between Up & Common – screen moves to up limit

• 

Contact is closed and opened between Down & Common – screen moves to bottom limit

• 

Stop command is sent when both Up & Down contact closed together

B. INFRA-RED RECEIVER

Packaged with 300mm and 2 M lead from motor board to IR receiver
Packaged with standard 2 channel IR transmitter
Screen operates on group 1 & 2 on infra-red remote
Green LED 1 on motor board will flash when IR commands are received

C. DC TRIGGER INPUT

• 

Down command is sent when a DC Voltage above 1.5 Volts @ 1mA minimum is applied to 
trigger input

• 

Up command is sent when a DC Voltage below 1.5 Volts @ 1mA minimum is applied to the 
trigger input

• 

Trigger input is polarity sensitive

• 

DC voltage must not exceed 15 Volts DC

D. IP INPUT

• 

DHCP (default setting) or Static IP addressable.

• 

Access for internal web browser.

• 

TCP/IP controllable.

INSTALLATION INSTRUCTIONS

 MasterFit IP A, A+, B, B+, C, C+ Projection  Screen 

Thank you for purchasing a Screen Technics Projection Screen, please ensure that you read 

the following instructions fully before installing this product. 

The motor controller for the MasterFit range of projection screens is housed in an insulated 

box and is packaged with a 1.2M IEC mains flex with moulded 3 pin plug and 240 volt output 

to motor is supplied with a 4 pin WAGO connector  with a 4M long  4 core flex allowing 

placement flexibility.  

1.

Contact Close Input

No voltage, dry contact input

Requires momentary contact only

Contact is closed and opened between Up & Common – screen moves to up limit

Contact is closed and opened between Down & Common – screen moves to bottom limit

Stop command is sent when both Up & Down contact closed together

2.

Infra-Red Receiver

Packaged with 300mm and 1.2 M lead from motor board to IR receiver

Packaged with standard 2 channel IR transmitter

Screen operates on group 1 & 2 on infra-red remote

Green LED 1 on motor board will flash when IR commands are received

 MasterFit IP A, A+, B, B+, C, C+ Projection  Screen 

Thank you for purchasing a Screen Technics Projection Screen, please ensure that you read 

the following instructions fully before installing this product. 

The motor controller for the MasterFit range of projection screens is housed in an insulated 

box and is packaged with a 1.2M IEC mains flex with moulded 3 pin plug and 240 volt output 

to motor is supplied with a 4 pin WAGO connector  with a 4M long  4 core flex allowing 

placement flexibility.  

1.

Contact Close Input

No voltage, dry contact input

Requires momentary contact only

Contact is closed and opened between Up & Common – screen moves to up limit

Contact is closed and opened between Down & Common – screen moves to bottom limit

Stop command is sent when both Up & Down contact closed together

2.

Infra-Red Receiver

Packaged with 300mm and 1.2 M lead from motor board to IR receiver

Packaged with standard 2 channel IR transmitter

Screen operates on group 1 & 2 on infra-red remote

Green LED 1 on motor board will flash when IR commands are received

STEP 1. 

Due to the length of the MasterFit boxes, the box will be subject to a slight twist from the 

tubular motor, the longer the box the more pronounced it is.

STEP 2. 

Mounting straps with eyebolts or threaded rod attached at the extremities, should be no 

further inboard than 300mm from the end of the box.

STEP 3. 

To overcome this twist, the ceiling and attachment points are used to stop the twist in 

the case.

STEP 4. 

Due to poor structural integrity of grid type ceilings, you may need to adjust the length 

of attachment method (threaded rod or chain with turnbuckles etc.) to minimise box twist.

STEP 5. 

Set ceiling installations are generally acceptable, with sufficient structural integrity to 

reduce box twist.

[email protected]

screentechnics.com.au 

AUSTRALIA

22-24 Suttor Road, Moss Vale NSW 2577

+61 2 4869 2100

NEW ZEALAND

44 Mahana Road, Te Rapa, Hamilton

0800 022 821

IN

 AU

STRAL

IA

PR

OU

DLY BUILT

ESTABLISHED IN 1990

Содержание MASTERFIT IP









Отзывы: