Scout Boats 245 Dorado, Руководство пользователя

Страница: 83 / 116

83
they will not take well to the surface and could appear spotty
and may also yellow or dull the Strataglass over time.
Strataglass can be cleaned by rinsing off dirt or salt deposits
with fresh water, then washing with a clean cloth and mild soap.
Chamois dry to remove water spots and improve clarity. If a
polish is accidentally used, use Windex
®
or its equivalent to
remove it. While window cleaners will destroy the standard
vinyl normally used in side curtains and clear connectors, it
will not harm strataglass. Always roll down the curtains and
snap in place at the end of each day so the curtains will maintain
their shape and to minimize fold distortions.
Depending upon usage, it is recommended that an occasional
application of Aquatech Strataglass Cleaner be done. Treat this
like a polish, as opposed to a cleaner - wash and dry curtains
first, then apply Aquatech Strataglass Cleaner, actually buffing
the surface to a beautiful sheen. This is not just a wipe on/ wipe
off product…it needs to be buffed to perform.
Remember, the coating on strataglass is scratch resistant and
not scratch proof. Always handle the curtains with care and
never roll up curtains that are salty or dirty. If you have any
questions about the clear curtains used on your boat, please
contact the Scout Customer Service Department.
The T-top enclosure must be removed when trailering. Canvas
enclosures are not designed to withstand the extreme wind
pressure encountered while trailering and will be damaged.
Always remove and properly store the enclosure before traile-
ring your boat.
CARBON MONOXIDE IS A LETHAL, TOXIC GAS
THAT IS COLORLESS AND ODORLESS. IT IS A
DANGEROUS GAS THAT WILL CAUSE DEATH IN
CERTAIN LEVELS.
Corian Surfaces
A mild liquid detergent and water or ammonia-based clean-
ers will remove most dirt and stains from Corian. For heavy
cleaning, oil, and grease, use Fantastik spray cleaner. Rinse
with a clean cloth moistened with freshwater. Wipe dry with
a clean cloth.
In most cases, Corian can be repaired if accidentally damaged.
Minor damage, including scratches, general or chemical stains,
scorches or burns, and minor impact marks, can be repaired
with a light abrasive cleanser and a Scotch-Brite® pad. For
heavier damage, light sanding and machine buffing may be
necessary so contact your dealer or a professional.
• Avoid exposing Corian to strong chemicals, such as paint
removers, oven cleaners, etc. If contact occurs, quickly
flush the surface with water.
• Remove nail polish with a non acetone-based polish
remover and flush with water.
• Do not cut directly on Corian counter tops.
Teak Surfaces
The teak and holly cockpit inlays are sealed with teak oil. It
is important to avoid tracking sand and dirt on the cockpit sole
and teak inlays. Sand and dirt acts like sand paper and will
eventually sand off the finish in the traffic areas. The wood
can be sanded and refinished as necessary.
We don’t recommend that you use varnish on the wood. The
wood grain is a natural nonskid and too much varnish or
polyurethane will fill the grain and make the wood slippery.
It is much better to us high quality teak oil to protect the teak
and holly inlays.
12.3 Interior
The cabin or head interior can be cleaned just like you would
clean a home interior. To preserve woodwork, use teak oil. To
maintain carpeting, use a vacuum cleaner. Because air and
sunlight are very good cleansers, periodically put cushions,
sleeping bags, etc. on deck, in the sun and fresh air, to dry
and air out. If cushions or equipment get wet with saltwater,
remove and use clean, fresh water to rinse off the salt crystals.
Salt retains moisture and will cause damage. Dry thoroughly
and reinstall.
Vinyl headliner material should be cleaned periodically as
explained in the previous section. Avoid using products
containing ammonia, bleach, or harsh chemicals as they can
shorten the life of vinyl.
If you leave the boat for a long period of time, put all cushions
on their sides, open all interior cabin and locker doors, and hang
a commercially available mildew protector in the cabin.
Note: always read the label carefully on mildew protec-
tors. Remove the protector and allow the cabin to
ventilate completely before using the cabin.
Interior Woodwork
Oiled and varnished woodwork can be cleaned with a damp
cloth. For heavy duty cleaning, use a mixture of water and Mur -
phy’s Oil Soap or a solution of 10% white vinegar and water
to clean the wood and wipe it dry with a clean towel. Apply a
furniture polish to add luster and help to preserve the finish.