Scout Boats 245 Dorado Скачать руководство пользователя страница 54

Страница: 54 / 116

The back of the helm station is accessed through a hatch in

the storage compartment just forward of the helm. This hatch

provides access to service the helm equipment, accessory

switch panels and other components installed in the helm. The

optional electronics are above the helm and accessed through

the storage compartment.

An acrylic door secured with a lockable flush slam latch pro

vides access to the compartment. The door could be damaged

or hurt a passenger by the motion of the boat if it is allowed

to swing free. It should be in the closed position and latched

whenever the boat is underway. A 12-volt light activated by

the Interior Light switch at the helm illuminates the compart-

ment.

Head and Storage Compartment

A large storage compartment and the head is located forward

of the passenger seat. A molded fiberglass door secured with

a cam lock provides access to the compartment. A grab rail on

the top of the door provides a hand hold for passengers.

The door could be damaged or hurt a passenger by the motion

of the boat if it is allowed to swing free. It should be in the

closed position and latched whenever the boat is underway.

The compartment is designed to store dunnage, three rods

and to accommodate the porta potti or marine toilet options.

It is equipped with a light that is activated by the Interior

Light switch at the helm and an ON/OFF switch in the head

compartment.

TO AVOID INJURY TO PASSENGERS OR DAMAGE
TO THE  BOAT,  ALWAYS  CLOSE  AND  SECURE
COMPARTMENT DOOR  WHENEVER VESSEL IS IN
MOTION OR IN ROUGH WATER CONDITIONS.

Rod Racks

There are two recessed rod storage racks located below each

gunnel in the cockpit. Another rod rack is located in the head

compartment. Always make sure the rods are properly secured

in the storage racks with the rod tips forward.

Fishbox Compartment

There is a large, insulated storage compartment located below

the cockpit sole, between the helm and passenger seats that can

be used as a fishbox. A drain rail around the hatch channels

water away from the compartment to a through hull fitting in

the transom. A diaphragm pump located in the stern bilge and

activated by the Fish Box Pump Out switch in the helm drains

the compartment.

Helm and Electronics

Helm Storage Compartment

Head Compartment

Содержание 245 Dorado





















































































































Результаты поиска

Содержание 245 Dorado

Отзывы:

Бренды по названию

Популярные бренды

Scout Boats 245 Dorado, Руководство пользователя

Результаты поиска

Содержание 245 Dorado

Отзывы:

Бренды по названию

Популярные бренды