Scotsman FM1200 страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 31

background image

FOR THE PLUMBER

CONFORM TO ALL APPLICABLE CODES

Water Inlet

Air Cooled Models: The recommended water
supply is clean, cold water. Use 3/8" O.D.
copper tubing, connect to the 3/8" male flare
at the back of the cabinet. Install a hand valve
near the machine to control the water supply.
Water Treatment: In most areas, a water filter
of some type will be useful. In areas where the
water is highly concentrated with minerals the
water should be tested by a water treatment
specialist, and the recommendations of the
specialist regarding filtration and/or treatment
should be followed.
Water Cooled Models: A separate 3/8" O.D.
copper line is recommended, with a separate
hand valve to control it. It is connected to a
3/8" FPT condenser inlet at the back of the
cabinet. The water pressure to all lines must
always be above 20 psig, and below 120 psig.

Drains

Air Cooled Models: There is one 3/4" FPT
drain at the back of the cabinet, the drain line
is of the gravity type, and 1/4 inch per foot fall
is an acceptable pitch for the drain tubing.
There should be a vent at the highest point of
the drain line, and the ideal drain receptacle
would be a trapped and vented floor drain.
Use only 3/4" rigid tubing.
Water Cooled Models: In addition to the
above mentioned drain, a separate condenser
drain must be installed. Connect it to the 1/2"
condenser drain connection at the back of the
cabinet.
Storage Bin: A separate gravity type drain
needs to be run, similar to the air cooled drain.
Insulation of this drain line is recommended.

AIR COOLED

MODELS

HAND

VALVE

FIELD

SUPPLIED

FILTER

WATER

INLET

VENTED

DRAIN

WATER

COOLED

HAND

VALVE

CONDENSER

INLET

WATER

FILTER

CONDENSER

DRAIN

VENTED

DRAIN

FM1200

October, 1991

Page 6

«
...
4
5
6
7
8
...
»

Содержание FM1200
































Отзывы:

Нет отзывов

Похожие инструкции для FM1200

Бренд: OBH Nordica Страницы: 24

Бренд: 3M Страницы: 23

deluxe bread and dough maker

Бренд: Oster Страницы: 60

Бренд: Hamilton Beach Страницы: 32

Бренд: Rachel Allen Страницы: 32

Бренд: Zojirushi Страницы: 17

Comfortbakery 99263

Бренд: Trebs Страницы: 6

Бренд: Carnival King Страницы: 3

Бренд: FUNAI Страницы: 14

Бренд: Hamilton Beach Страницы: 64

LabelManager 210D

Бренд: Dymo Страницы: 13

Бренд: Bialetti Страницы: 64

Бренд: Caffitaly System Страницы: 64

GE-2406T Series

Бренд: Gainscha Страницы: 33

Бренд: Saeco Страницы: 33

Бренд: Saeco Страницы: 48

Бренд: Flair Страницы: 2

Бренд: Lakeland Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды