Scotsman FM1200 Скачать руководство пользователя | Manualshive

Страница: 18 / 31

background image

///////////////////////////WARNING/////////////////////////////
Disconnect electrical power before
beginning.
//////////////////////////////////////////////////////////////////////////
5. Clean the air cooled condenser.
The air flow on this model is from front to
back, so the inside of the machine will have to
be available to clean the air cooled
condenser. Use a vacuum cleaner or coil
cleaner if needed. Do NOT use a wire brush.
A. Disconnect electrical power, and remove
the filter. The filter may be cleaned or replaced.

B. Clean the condenser: the condenser may
appear to be clean on the surface, but it can
still be clogged internally. Check with a flash
light from the front to see if light can be seen
though the condenser fins.
Reverse to reassemble.

MAINTENANCE: Air Cooled

Step 3: Pull fans

& bracket up and

off locating pins.

Step 1: Remove

top panel.

Step 4: Clean the condenser.

Step 2: Remove

two screws and

unplug fans.

FM1200

October, 1991

Page 18

«
...
16
17
18
19
20
...
»

Содержание FM1200
































Отзывы:

Нет отзывов

Похожие инструкции для FM1200

Бренд: Kalorik Страницы: 24

Бренд: U-Line Страницы: 19

Бренд: Follett Страницы: 44

Бренд: TAKE-A-LABEL Страницы: 6

Бренд: Saeco Страницы: 52

Бренд: Hamilton Beach Страницы: 36

Бренд: La Pavoni Страницы: 72

DIPPING CABINET SERIES

Бренд: Randell Страницы: 16

Бренд: Salton Страницы: 10

Бренд: Mr. Coffee Страницы: 14

Бренд: Menuett Страницы: 16

Бренд: BRAYER Страницы: 52

Бренд: Hamilton Beach Страницы: 28

Бренд: U-Line Страницы: 53

i-Joy Cafe Ultimate

Бренд: Beem Страницы: 100

Moltio HD8768 AMF

Бренд: Saeco Страницы: 3

Бренд: La Pavoni Страницы: 178

Nespresso Vertuo Plus

Бренд: Krups Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды