Scotsman ECC0800-32E Скачать руководство пользователя страница 7

Страница: 7 / 32

EH222 E and Condensing Unit

Remote Low Side Cuber User Manual

June 2017

Page 7

Pre-Installation Details

Note: The ice making section cannot be stacked

vertically.

Accessories such as bin adapters and tubing kits are

required to complete the installation.

Dispenser Adapter Kits:

•   Cornelius ABS: KBTABS  ED150: KBT40
•   Scotsman ID150: KBT40
•   Scotsman ID200 or ID250: KBT41

Bin Adapter Kits:

• B530P or B530S: KBT32
• B948S: KBT34

Tubing Kits:

•   20 foot: 3BRTE20-EH
•   35 foot: 3BRTE35-EH
•   50 foot: 3BRTE50-EH
•   75 foot: 3BRTE75-EH

Note: Line set may have quick connects. The

condensing section may have quick connects. See

refrigeration system detailed instructions connection

details.

Items required for installation:

• Ice making head
• Condensing unit (includes interconnecting control

system wire)

• Tubing kit. 20’, 35', 50’ or 75’ triple line set (liquid,

vapor and suction)

• Bin or dispenser adapter

Special Considerations

The ice making section’s footprint is 22” wide by 16.5”

deep. The refrigeration connections can be routed up

or to the back. The drain may be routed out the back

at any position left to right; it may also be routed to

either side.

Water

Pure water does not exist. All water supplies contain

some amounts of impurities, although potable water

is, by definition, fit for human consumption. Because

the contents of the water to an ice machine directly

impact its performance, consideration should be given

to improving the water’s quality.

There are two ways water can contain impurities:

in suspension or in solution. Suspended solids can

be filtered out of the water. In solution or dissolved

solids must be diluted or treated. Water filters are

recommended to remove the suspended solids.

Some filters or filter systems have treatment

chemicals in them for treating the suspended solids.

This ice machine has an adjustment for the amount

of water rinsed or purged. Water use adjustments

are customer convenience adjustments; they are not

factory defects and are not covered by warranty.

Содержание ECC0800-32E

































Результаты поиска

Содержание ECC0800-32E

Отзывы:

Похожие инструкции для ECC0800-32E

Бренды по названию

Популярные бренды

Scotsman ECC0800-32E, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ECC0800-32E

Отзывы:

Похожие инструкции для ECC0800-32E

Бренды по названию

Популярные бренды